Good day to you, I would really love your insight on this cisco phone that I'm troubleshooting at the moment, we noticed last week that the two phones just gets lit up anytime power is applied to it, it doesn't boot up/load firmware, it just illumina...
Forum Posts
Hi,We are periodically facing CUCM high CPU caused by tomcat1 process and it leads to server crash and only resolved by hard reset of CUCM.here is the network diagnostic result:The following web applications have an unusually large number of active s...
Hi, We are periodically facing CUCM high CPU caused by tomcat1 process and it leads to server crash and only resolved by hard reset of CUCM.here is th network diagnostic result: The following web applications have an unusually large number of active ...
Hello everyone, I'm experiencing some issues configuring a simple text label on a SIP third-party device. I registered correctly the SIP device on the CME but when I try to call any internal phone (Cisco IP phones), I cannot read the label text, but ...
Last week Our Cisco CP 7821 phones two of them, developed some faults, the screen just gets lights up and without it loading up the firmware, the handset RED light comes up as well. But the phone does not boots up.All forms of reset has been done.:> ...
I have created a hunt pilot 4305I have a line group of 4 members in that hunt pilot (4087, 4088, 4091)Set to ring to the member with the longest Idle time, the stop hunting, preferably, I would like the call to continue hunting until it tries all mem...
Resolved! 7975 ip phone unprovisioned
hello, i have a SIP 7975 IP phone (sip75.9-3-1sr2-1s) that i moved from one CUCM deployment to another. initially the phone would not be able to get past the existing CTL and ITL trust list it had from the original CUCM deployment; after checking con...
We recently decide to setup a warm standby CUBE as a backup to our primary CUBE. We used a copy of the existing CUBE config with everything identical expect the IP **bleep** of the new CUBE. Very soon after the standby CUBE came online users report...
Hi I want to some old CDR data information from CUCM. I have old backups with CDR_CAR.tar file, but I am unable to open them. Is there a way to open those file and get the CDR dumps? Thanks Sakun
recently replaced older UCM system with cisco 7800 series phones registering back to HQ and call manager. The site has an existing Algo 8301 paging adapter connected to a legacy amp and speaker system. I was able to configure a 3rd party user in CU...
Resolved! Users Voice Mails
Hello Members, I have CUCM and CUC integrated over SIP trunk, In CUCM side : I Have Voice Mail Pilot Ext 800 and Voice Mail Profile, Also have 2 route pattern to CUC over sip trunk 1- Route pattern 887 to IVR number in CUC over sip trunk, when call...
Hi All,I have an EXSi PAK from Cisco and I have to register it in order to run VM's on my call manager.The VMWare site for product activation is down,can anyone suggest a work-around solution?In addition,can I activate Cisco FLEX licenses without reg...
The outbound calls from CUCM to Webex Calling are failing, and an error SIP message is being received.SIP/2.0 488 Not Acceptable MediaVia: SIP/2.0/TCP 192.168.1.20:5065;branch=z9hG4bKd1e23d546546Warning: 399 192.168.1.100 "SRTP Offer/Answer not accep...
I installed ip phone 840 and need to configure corporate directory through admin setting but it said read only , how to enable setting on cisco 840
My 7940 is bricked, and when I try upgrading firmware, it gives me "TFTP File Not Found". The TFTP server says that the phone is looking for "MGCDefault.cnf", and "SIPDefault.cnf", and other files. I've read that it may be because I am trying to upgr...
