Network Management

hello,I have an WS-X6708-10G-3CXL card (8 port 10G x2) in an 7606-S router. the card has two "fire asics" and four "fpga muxes"Does anyone know if there is a MIB for polling utilization for "fire asics" and/or "fpga muxes" ?I'd like to be able to pol...

Inventory poller job shows all devices "Not attempted" status, it's scheduled every day, but finishes with the same result all the time.LMS 3.2.1

Hi all, I hope some of you can help me with a doubt I have.I need to add lots of devices to CW LMS and there's some info I can't find anywhere. What device credentials do I need to manage the devices (not device discovery)?? I'm not sure if SNMP RO+R...

Hello Experts,our customer has a working integration with the Cisco Works LMS 3.1 and an ACS v3.3 as it is described in this document:http://www.cisco.com/en/US/prod/collateral/netmgtsw/ps6504/ps6528/ps2425/prod_white_paper0900aecd80613f62.htmlNow we...

Hy.I need to roll out an IOS on r.a. 250 devices. But when I try to distribute any software image via RME I always get the same error. I'm unable to start the job because in step one after selecting image and devices I get "failure" for all devices. ...

HiI'm really quite new to LMS, but we did make one attempt at trail version 4.0.1.Unfortunately I can not install it on a windows 2008 r2 64-bit server WM host. I'm currently running 4.1 EXS do not know if this is supported.No matter what I do I get ...

HiWe are using LMS 3.2 running on windows 2008 server . When i am tying to create a job i recieve an error " DCMA0077:Could not create job. Check dcmaclient.log for more details. "The CTMJrmServer process is not getting started . tried restarting the...

Problem:Cisco box is not forming ntpv4 association with juniper box over IPv6 addressScenerio 1:I tried to configure cisco box(7200 series loaded with c7200-ipbasek9-mz.124-24.T5.bin)  as ntp client to a juniper box. Both the boxes supports ntpv4 and...

Hi Guys,Does anyone know the procedure to do an LMS upgrade from 2.6 to 4.0.We will be needing new hardware so I will do a fresh installation of 4.0. Can I restore a 2.6 backup in LMS 4.0. Or do I have to reconfigure from scratch...Thanks,Best Regard...

Hi ,i have a problem with DFM 3.2 , where it shows unknown devices:1- Cisco Catalyst 3560V2-24PS Switch(WS-C3560V2-24PS) 1.3.6.1.4.1.9.1.10212- Cisco Catalyst 2960-48PST-L Switch (WS-C2960-48PST-L) 1.3.6.1.4.1.9.1.1016it is showing as supported in ci...

When I try to upgrade to LMS 3.2.1 on my Server 2003 server running CS 3.3.0, CW Assistant 1.2.0, LMS Portal 1.2.0, and RME 4.3.1 it hangs on "Looking for locked files."   Anyone experienced this before or know what casese it to hang on this step?

What is mean (ED) in the picture?I tried to download IOS and I don't understand the (ED).

We use "skeleton files" to enforce certain configuration commands to all devices. Skeletons are based upon platform, IOS/catos, etc.For example:logging buffered infologging console debuglogging monitor debuglogging buffer 16384logging trap informatio...

Hi,We are currently running LMS 3.2 w/ 300 deivce license. I have several questions regarding the upgrade kit to be purchased,Form what I have understood, the upgrade kit CWLMS-4.0-300UPK9 can be used to upgrade the existing installation or even inst...