I have 1760 hooked up to MPLS of AT&T, and some reasons, it work off/on when I ping to the box. Is this something I should look at in my box?
I have 1760 hooked up to MPLS of AT&T, and some reasons, it work off/on when I ping to the box. Is this something I should look at in my box?
Hi,I need to create a full backup to my server and my application Cisco Works.Because tomorrow i will update from the version LMS 2.5.1 to LMS 2.6.How can i create the backup?
Hi,Please help me do a snmp walk on a pix 6.3 and 7.X to get the arp table.thanks in advance.RegardsSalim
Hi All,I know that NetFlow reports ACL blocked traffic as flow with Null destination interface index. What about the packets dropped in Qos Queues. Does NetFlow report the packets dropped in the Qos queues also?RegardsRam
Here are some more little quirks with baseline templates. 1) The job status is ALWAYS "failed". I think that when a command responds with output of any kind it triggers a failed condition. Thus, attempting to remove a non-existent snmp community (...
Hi,We have around 4 devices that just started receiving this error++++++++++++++++++++++ CM0057 PRIMARY STARTUP Config fetch SUCCESS, archival failed for sfsl-access-sw05 Cause: Internal error Action: Verify that archive exists for device. CM0061 PRI...
Has anyone used ZENworks for Networks or cirrus as a config management tool and if so what are your views on them. I am particularly intrested in if the ZENworks tool is any good. All help is appreciated
Hi!is there any software or tool that can give exact bandwidth usage? im using netflow now but it seems that it doesnt detect the exact bandwidth on my serial interface. if someone knows. please post it.tnx a lot
What support is available for the PIX firewalls in LMS2.6 ?.RegardsScott
I am running jitter with 729a codec on 4948 to responder on 12.2.18SXF. It produces different results comapred to regular type jitter with the same parameters but without codec. D-S jitter and OW delay is twice greater than S-D. Sender has 6ms offs...
Hi, when I try the inventory report I got the following message:"The selected device does not have inventory data to display in the report"Everything seems ok on credentials and I other 3 devices (same hardware) that I am not facing the problem.Any i...
I am relatively new to CiscoWorks and am not quite sure which document to try and look up this information. Our company is using CW for switch configuration. Switches also send in their data via syslog. My question is: Is it possible to configure CW ...
Hello All:We are doing some measurements with a software that uses the following MIBs from Cisco Routers:rttMonJitterStatsMinOfMOS (1.3.6.1.4.1.9.9.42.1.3.5.1.56)rttMonJitterStatsMaxOfMOS (1.3.6.1.4.1.9.9.42.1.3.5.1.57)We need to know if the results ...
Hey Folks,In Device Manager, I'm trying to update to the latest package for Rtr1800, Rtr2800, Rtr3800, and Rtr800 to the latest versions. After I select them and click next to install it, I get the following error:"base package NGMARShare missing"A...
I need to monitor ports locally and remotely, can I have 2 different sessions have the same destination interface?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-21-2024 04:04 AM | ||
10-18-2024 12:32 AM | ||
10-16-2024 04:14 PM | ||
10-10-2024 01:25 AM | ||
10-03-2024 12:07 PM |
User | Count |
---|---|
3 | |
2 | |
1 | |
1 | |
1 |