Hello,I'm trying to turn up an AT&T megacom PRI using 4ess on a 6608. Inbound calls complete successfully but outbound calls fail. AT&T is telling me that I am missing an IE tag "megacom". Anyone know how to do this from CCM? Can anyone point...
Hello,I'm trying to turn up an AT&T megacom PRI using 4ess on a 6608. Inbound calls complete successfully but outbound calls fail. AT&T is telling me that I am missing an IE tag "megacom". Anyone know how to do this from CCM? Can anyone point...
Hi guys,how can i degrade a ccm publisher to be a subscriber?Mike
I am receiving the following error when access Fast Dials from 7960 phone:Error: -7ffbc17c: Accessing an empty list.Note: this is not an invalid password error.Any ideas??
Hi all,I knew someone asked this questions a while ago. But seems like noone can solve the problem.CCM4.13sr3cEverytime I press services button, it will ask me usernmae, password and realm.Anyone know why???Thanks a lot!!Ken
Is there a way to bulk update the department field in Callmanager 4.1
We are implementing a IPSEC VPN Connection over leased lines using cisco 2821 without AIM-VPN Hardware accelerators.The line is 2 Mbps and should carry also IPtelephony traffic (4-5 conversations). Will we have problems by mastering the jitter? Since...
During a new 4.1.3 call mgr install, 7961 phones hung during bootup. Had to remove the followimg cmds from the 3750 stacks to get them to boot:Removed ip verify source from each interfaceRemoved ip arp inspection ?vlan info? from global configRemoved...
I am wondering if this feature is available for us to test the analog line number from patch panel by a line tester?Say I dial a specific number and get audio answer of the DN number I am dialing from.
Hi,I`m new to IP telephony, have completed most CCVP courses so I am quite familiar with Call Manager. However, I am unsure how IPCC enterprise intergrates with Call Manager in relation to call routing etc... Suspect that this is done through CTI. An...
Having a strange problem on a new site turn-up. Have a 265x XM at a remote site connected to CCM. 2600 has 4 pots lines for inbound/outbound calls. Once more than one pots line is connected (no difference if call was inbound or outbound) the 2nd,3...
Dear All,I'm trying to Configure IP Communicator on using "optimize for Low-Bandwidth".What has to be enabled on CCM or at the SRST in order to achieve internal and external calls?Thanks,YV
If A calls B and B has a Call Forward All to C, then C cannot transfer back to B (this functionality was available in the customer's legacy PBX). Is there a workaround?
Hi,I have the following setup:CCM 4.0(1)sr2a, one publisher, two subscribersIPCC Express, CRS 3.5(1)4 sites with 2800/3800 as gateway (PRI/BRI)Main site (Netherlands) holds call center agents (20) with several queues.New request from business is to h...
Any way simple login the EM? for example, press * and change the phone to EM with skip "Service button > select EM > login". I know how to one-time-login to skip the userid and pin but want to know more simple way.Thanks in advance,
HiI have a couple of FXO ports on my gateway, my clients dial 0 for PSTN access, However I do not want outside callers to dial 0 when calling in to my gateway and be redirected to pstn again.Is this possible? what must be done? can any one help me ou...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-23-2024 11:56 PM | ||
08-21-2024 05:48 AM | ||
07-17-2024 05:55 AM | ||
07-15-2024 12:39 PM | ||
07-09-2024 04:24 AM |