At the moment Slot2 redundant supervisor becomes active all the time.I want to make Slot1 Supervisoer as active all the time, except when there are problems with this slot,Please advice if any special command is available to make this happen.
At the moment Slot2 redundant supervisor becomes active all the time.I want to make Slot1 Supervisoer as active all the time, except when there are problems with this slot,Please advice if any special command is available to make this happen.
I have 2 6509's connected via 3 port Gigabit Etherchannel 6509A has a Supv II and 6509B has Supv 720 on the 720 side I see input errors on the port-channel and on the ports themselves, on the 720 side with the port-channel interface I have it set to ...
What is the difference between 7507 and 7507 MX chassis? Where can I find info about this ?Best Regards.
hi in my central router i have 3 VMIC-2MFT-E1 cards so from one card (2 ports) i want to connect to 2 different branches, only data is it possible using this card. Binoy.
Am trying to get a wic-1enet to address in a 1720. I realise to do this there was a specific IOS ver to use. As well the WIC would only work in WIC0 unless 12.2.xxx was used. My prob is identifying the right release on the download centre. Tech d...
Hi,we have a big network with nearly 1000 routing entries. When i made a "show ip route" i can saw that the 95% of the entries are "new".Example:O IA 198.0.140.0/24 [110/103] via 10.26.4.29, 00:05:00, Vlan11O 4.192.198.0/24 [110/4] via 10.26.6....
I have a non cisco switch, on which I am mirroring the traffic from port 24 to port 23. Port 24 is the source and port 23 is the destination. I have checked by connecting sniffer to this port and it is working fine. Now starts the funny part. One...
I am in the process of adding a second ISP for my internet connection, what would be the best approach to load share the outbound data between the two ISPs?
I have a 827 router, it's connected to the Internet via the ADSL port and I use NAT to connect multiple computers and share the one public IP I have.One computer needs to be accessable from the internet for a service running on port UDP 8088 to 28088...
I've been given the task by my employer to build a new network, I've purchased what I thought were all the needed bits and bobs, but I just can't seem to get the final bit to work. I have an ok amount of experience with Cisco gear, and I can fumble ...
hii have following setupinternet-serial-router-eth0/0-pix(outside)-pix(inside)-lani hope it makes sense..i configure pix outside interface for public ip and i configure pix inside interface for private ip and i configure pix to do natingnow, here is ...
I have a cisco 1700 and 1750, both with T1 csu/dsu Wic's. I am connecting these via cross over cable and they are not connecting. I have also used a straight through cable as well. Assuming ip addressing is correct. Should these be able to work o...
Can I use a XENPAK-10GE-LR in a X6704-10GE blade in a 7613 with SUP720-3BXL? I am trying to configure a new 7613 and need LR support back to our IBM Mainframe.
Hi,Anyone know if high rate multicast traffic on Cat2950 with default IGMP snooping enabled will cause messages lost?Read from book that Cat2950 process IGMP snooping at hardware level but will there be possibility the switch can't handle high rate o...
Recently , I build up two site to running IBGP , but i found it look like loop according with "sh ip bgp neighbor X.X.X.X" command : AS_PATH loop: n/a 9508anyone can tell me how can i resolve the problem
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM |