Here is our setup. One RSM connected to two 7xxx routers at both ends of ATM circuits.6509 RSM |---->7204----ATM circuit 4Mb ------<--7206----| RSM 6509 |----->7206---ATM circuit 4 Mb-------<-7204----|We notice poor load balancin...
I installed a fast ethernet adapter in two 3640’s which are both connected to 4006’s, one is in my building and the other is in a remote location. Both 3640’s and 4006’s are running the same level of code. When I installed the one in my 3640 and po...
Hi,I have a little problem, because I need the serial Number from some Power Supplies installed in Catalyst 4506, wich are not stay in my country.Can anybody tell me how I can get the serial numbers from the power supplies in a Catalyst 4506 Chassis ...
Dear ColleaguesI have a Cisco standard cable (smart serial, V.35 3m) i want to extend this cable, can i have the pin assigment and the max length i can extend the cisco standard cable with.Best RegardsAbdel Fattah Elsherif
RIP doesn't allow to specifically put network statement unlike ospf and newer verison of EIGRP.If for example r1's s0 is running rip, and s1 will be running ospf in the future. r1's s0 is connected to another r2. so r1 configint s0ip address 170.1....
We try to implement a solution for resilience in case of equipment failure.My question reffers to the following:- I have a Cisco 2621 router with two E1 interfaces and 1 FE. The router is the standby one for the active router existing in local networ...
I remember rs232 speed is up to 19.2 kbps,but why I can config clock rate to 128000 when I plug the 232 DCE cable to 2611's nm-8a/s?I can't understand.Is cisco's rs232 enhanced rs232 or something else ?thanks!
I experienced reboot of R1603 router once I issue "Show ISDN status" command. The problem is not intermittent but consistent as it happens on 2 routers (both are R1603) with IOS Version 12.0(3)T. Other "Show ISDN" commands such as "Show ISDN active...
any body has explanation why the calculated metric by router is 5005056 while if u try to calculate it by equation it gives a different result 256(20+(10^7/512)=5005120 note that:Ks values are defaultoutput shown from sh ip eigrp topolgy 10.10.10.0--...
Hello,I've got a 2620 with a 4-BRI module. The 4 BRIs are configured in a hunt group by the telco.I will have several customers which will get connected to this router, each will have his DIaler interface.I put all the dialer interfaces in the dialer...
I need to setup a 2600 on a PRI circuit to statically route seperate IP networks to branch offices where the remote sites are both on occasion dialing in and being dialed from the main site. The remote sites are using Shiva Access Ports and were prev...
HelloWe have an internal debate with some colleagues in my company, regarding a change in our OSPF configuration, due to external restrictions, that oblige as to introduce a Router connected to 2 areas (none of them the Backbone area).I have 2 questi...
Hi... I have a question...I have a router cisco4700 has a FastEthernet and a 6-port Ethernet.Two L3 3550 switchs are connected to it. One is connected to FastEthernet, and another is Ethernet. Router 4700 can find one of the switchs via FastEtherne...
If I remove the CDP command from a cluster interface the device will still show up in the command cluster topology view? How detrimental is this to Security? Ie I have a vlan with wireless devices on it and i can see those devices from the network to...
the following is the configuration of a router's interface:!interface FastEthernet1/0 ip address ..................... no ip redirects ip wccp web-cache redirect in ip nat inside ip route-cache flow ip policy route-map TEST speed auto full-duplex!Wha...
