Routers - Small Business

Hello,Our RVS4000 router will not save any static routes.  Under advanced routing, we add our network, mask and gateway, but, when we click SAVE, the information is deleted.  Tried add various different routes (networks: mask 255.255.255.0 and indivi...

Hi all,I need to build a VPN tunnel from my Android  smartphone to Cisco RVS4000, but looking on some Internet forums I  understand that I can't build a VPN tunnel between a smartphone and the  router I purchased. Can you confirm this aspect? I am do...

Hi, i have a SRP526W and it won't boot correct, nothing is changed, I just turned it off and changed the place, now it won't boot. The POWER/SYS LED flashes and DSL Data LED is solid green!! Can someone olease help me with the problem? THX.

Sorry, this is an age old story but I have to touch on it again.I used to have the problem where QuickVPN keeps on trying to verify the network because the RV042 cannot get the final ping to the client.I then bought a RV042 HW version 3 on the VPN si...

Today the power was fallen out in our area and the rv042g was turned off.After the power was back I was checking the router because some trafic didn't came through.Then I saw that all the services were messed up and also all the firewall rules were w...

Hi ThereI have a RV220W with the latest firmware (1.0.2.4) and I loose about one in every 20-40 packets. I have tried with both wireless/wired, on different ports, laptops, and Ethernet cables. My configuration is fairly simple:1.) I reconfigured the...

For the past week, I have tried to setup the PPTP VPN server on the RV180. The setup was straight forward, but I could not log-on no matter what I tried. I decided to call Cisco small business support, and as I was talking to the engineer, it mysteri...

Hi,I have a pair of SRP527W-U units, which each connect to a seperate ISP by ADSL2+I am attempting to use each simulatenously as follows:ISP-A via CiscoA for general traffic, and to run HTTP server XISP-B via CiscoB to run HTTP server YHTTP servers X...

Hi, Anyone can advice ?I have 2 sites located 500 meters away and i connect it via 2 x RVS4000.I managed to get the site to site VPN up Via internet and from my network 192.168.1.x able to reach 192.168.2.x.-where 192.168.1.100 (user try to acces my ...

I have an RV042 firmware 4.1.1.01-sp with client vpns established. I have one end user that can connect every time with now issues whatsoever. I have other clients that can connect, but are often dropped. The first day they connected for up to 8 hour...

i have the RV082 v03 i set it for load balancing i have 2 8gb Adsl modem connected to Wan1 and Wan2Question how can i assign a certain pc to use the connecton on Wan2, what i would like is to assign a specific pc on the network to wan2 

The following caveats on the RV042 are acknowledged in release 4.2.1.02:Problem: When multiple phones on the LAN use the same SIP port, the router will change these SIP ports on every registration. This can affect existing inbound calls, where the fo...

Hello,I gave setup a vpn gateway between two cisco RV120W. The connection is established.Active IPsec Security Association TablePolicy NameEndpointPacketsKBytesStateActionRxTxRxTxVPN-INTERDIO87.65.38.62000.000.00IPsec SA EstablishedPoll Interval:(Sec...

I've been noticing that occasionally our 2nd Gen RV082 fails to allow internal admin management until a manual restart.  After the restart, all seems to be fine and traffic/router is very responsive. The following describes typically how the issue oc...