Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

                   Hi,We are getting below log message in one of our Internet Facing RouterPls confirm whether we are under attack or not000092: Aug 17 15:11:21.584 IST: %IP_VFR-4-TINY_FRAGMENTS: GigabitEthernet0/1: from the host 64.39.111.57 destine...

Hello I have a 1841 router which i am using as firewall/NAT/routing between vlans etc. Currently i have the router on a stick setup. I have two interfaces, one Fa 0/0 is connected to my ISP's VDSL modem and i am using Dialer1 to do the PPP authentic...

sphinx_uk by Level 1
  • 1869 Views
  • 6 replies
  • 0 Helpful votes

Hello Cisco community, Need help with Vlan tagging on switch Catalyst 3750 series PoE - 24  Vlan ID 1 Ports 1- 8 untagged 50,70 tagged Vlan ID 50 Ports 9 - 16 untagged 1,70 tagged Vlan ID 70 Ports 17-24 untagged 1,50 tagged 9 - 16 have access to vlan...

I am trying to use the AUX port on a ASR 1002 to connect to a console port on another router. Usually you telnet to port 2000+line number and then you are on the AUX with an outgoing connection. But I can not figure out how to do this on ASR. I am ru...

Resolved! VRRP

what's meaning of " track 1 interface f0/1 line-protocol" and " vrrp 1 track  decrement 60" ?

Hello, guys. How do I know if ntp is synchronized or not? The output is the following: show ntp peer-status Total peers : 1* - selected for sync, + - peer mode(active), - - peer mode(passive), = - polled in client mode remote     local     st pol...

I want to add a static NAT in 3650 switch. I tried it but I couldn't find static NAT ('ip nat inside source static' command is not there). I added a  dynamic NAT using ACL. I want to change change 1.1.1.1:99 to 2.2.2.2:99 so I only put  1.1.1.1 in th...

Hi Expert, Today i was doing very small BGP lab where have only 2 router and had IBGP peering between 2 nodes.i playing with distance command in my lab, but when i changed AD of iBGP routes and run command "clear ip  bgp * soft"  bgp policy not ge...

praverai by Cisco Employee
  • 1252 Views
  • 2 replies
  • 0 Helpful votes

Hello Experts, I am getting the error... %DUAL-5-NBRCHANGE: IP-EIGRP(0) : Neighbor xxx.xxx.xxx.xxx (GigabitEthernet1/0/2) is down: K-value mismatch I checked theK values by using "sh ip protocols " command.. He is the output:  R1: EIGRP metric weig...

Which technology would you implement if multi-tenancy is required over consolidated WAN cloud: LISPoDMVPN or 2547oDMVPN? There're some rumours that 2547oDMVPN can be officially supported with IWAN 2.2 in the near future. LISPoDMVPN looks a little bit...

I've been researching how to properly implement for a specific BGP scenario.  In my research I may vary well have come across the bits a pieces that I need to accomplish this but have yet to simply find it presented in a way that clearly meets my nee...

rath514 by Level 1
  • 305 Views
  • 2 replies
  • 0 Helpful votes

I have an issue regaridng EIGRP and VLANs. I have two layer 3 switches connected together via a /30 subnet. Both of these switches have the same SVI (VLAN 99) for management and are showing up/up. From Switch1 I am unable to ping the VLAN 99 interfac...

nohara by Level 1
  • 2737 Views
  • 2 replies
  • 0 Helpful votes