HI Everyone,I have cisco 2611 + NM1E , and i want to trade in for a cisco 2911 security router + HWIC4 CardWhich type of HWIC card should i use in the cisco2911-sec/k9 router?brsam
HI Everyone,I have cisco 2611 + NM1E , and i want to trade in for a cisco 2911 security router + HWIC4 CardWhich type of HWIC card should i use in the cisco2911-sec/k9 router?brsam
Hi Guys,Has anyone connected an analogue modem to the CON/AUX port of a 887VA for remote provisioning yet? We do this all the time with 877's but things seem to be a little different the 887VA as we get nothing out of the router's console port once t...
I have configure 887 ADSL router with attached configuration. But users cant access internet properly. (Ex: yahoo and gmail mail cant access)Therefore please check the configuration with my network design which I have attached.Thank you,Chandimal.K
Hi Netprowhen y configure EIGRP as ur routing protocol, why y add a static route pointing to next-Hop?Thanks
When the router boots up, the boot loader keeps telling me it does not recognize the card and wait until it fully boots to see the revision on the card, but I can not see the revision on the card because it is unrecognized.Does anyone know what boot ...
Hi,In our cisco 1841 there are two ISP MPLS link.what dose mean the below configuration.what is the use of prefix-list??how it is works??ip prefix-list BSNL-LANROUTES seq 5 permit 172.16.0.2/32ip prefix-list BSNL-LANROUTES seq 10 permit 10.10.30.0/24...
I have a Cisco 857 which seems to be dropping connection on its public internface.I would like to see the logs of the ppp or something which may help identify the problem of why the device has lots its connection.I know what you can setup logs for a ...
Dear Experts,I have 2 Cisco routers 3945. Use HSRP for links failover. Does exist any possibility (any protocol) which makes routers configuration's automatic synchronization (as failover for ASA firewalls)?I mean, if I will make any configuration ch...
Hello,I've got a problem that I'm hoping is simple for someone out there!We have an ASA 5520 in production with a brand new internet feed we've just finished installing. We connect to our corporate office via a VPLS. In our corporate office we have a...
How can I manipulate incoming traffic from a specific prefix from my ISP to come through my other ISP to elevate the traffic on my 1 peer router?I have the following setup:ISP-A ISP-B | ...
I've connected a dslmodem/router to a fast ethernet port(fa0/1) on a 2620 router.There is a 2950 switch connected to the other port (fa0/0).I can ping the Internet via the router but and the switch but not from a host connected to the switch.I can't ...
Ok so this is my first time dealing with CISCO. I am enrolled in CISCO 1 and I am having trouble with one specific part. How do you Assign an IP address and an network mask for an interface? And hhow do you assign an IP address, Netmask, and a gatewa...
I have a 1t3/e3 card in a new 2951. When I statred the router, I found no interface corresponding to this module when do "show ip interface brief"any idea?thanks,Han
Hi Netprohow many module like NM-8CE1T1-PRI the 3945 support,i m looking to have 24 E1 Cards on the same router (3) of NM-8CE1T1-PRI,is it possible?Thanks
HiAssume I have two sites, each have two routers and two ISPs providing MPLS VPN service to me. Site routers use OSPF two exchange routes. ISP offer BGP as PE-CE routing protocol with the use of private AS numbers.So here are my thoughts about the wh...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-13-2024 03:21 AM | ||
07-11-2024 01:54 PM | ||
07-09-2024 05:41 AM | ||
07-03-2024 08:54 PM | ||
07-02-2024 04:20 AM |
User | Count |
---|---|
14 | |
5 | |
4 | |
3 | |
2 |