Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

Hello,We are planing to design VPN solution, but we're unsure what would be the best approach where to install the VPN router based on the security/performance. Our goal is to have the router handles about 100 site to site VPN tunnels, and firewall h...

Joe Lee by Level 1
  • 956 Views
  • 5 replies
  • 0 Helpful votes

hi i Have one customer he has router 2811 and need assgin detceded ip address to each computer for Emaple : Ip telephony No need to assign exectly ip adress 192.168.100.50other ip phone assign exectly ip adress 192.168.100.51please anyone advise me t...

http://www.cisco.com/en/US/tech/tk389/tk815/technologies_configuration_example09186a008019e74e.shtmlwe setup our switch according to the document linked above.  The nodes in the vlans can ping each other.  The switch can ping the router.  However, th...

I am trying to implement RBSCP on two 3845s running 15.1(4)M1 Adv Enterprise over a satellite link.  The "show" commands all look correct, but whenever I policy route my machine through the RBSCP tunnel I dont even make it to the opposite side.  Howe...

A company's network is spread over six locations.six different-2 cities.Headqurter is situated in Sydney and branch offices are located in the other cities.on the headquarters office OSPF network is running and branch offices are running bgp networks...

Hi all,I am new to VRF  and in particular VRF Lite and would like to gain some insight into its potential uses.  In particular, I am looking for a cost effective solution to extend customer sites into a datacenter.  The "extend" part of this solution...

I have 2x 1941 routers that i connect both WAN interfaces to a Netgear DSL router or I connect all three connections to ports on the same vlan on my 2960 switch. I configure the WAN interfaces on the router to receive IP address via DHCP.None of rout...

akintokun by Level 1
  • 732 Views
  • 1 replies
  • 0 Helpful votes

Hi,I guess this is more of a service provider question.  If i wish to upgrade from a T1 to a T2 frame relay connection, apart from changing the bandwidth on the serial interface on the router, are there other changes required as well?Thanks.

We currently have an existing 3945 doing BGP with our ISP. We'd like to put in a second router and utilise HSRP on our internal side to improve redundancy. Our ISP has suggested we do separate BGP peering sessions on the 2 routers towards them and us...

Hello all,I was just wondering if the following was possible and if not, why oh why is it still not possible ? I want to implement outbound traffic shaping based on the originating AS number The router has a WAN interface over which it runs BGP. It r...

gnijs by Level 4
  • 1150 Views
  • 5 replies
  • 0 Helpful votes

Hello!I have CISCO 7206 router with NPE-G2 and 2 gig of memory.There's a vpn and pppoe servers on this unit and it hold maximum of 250-300 simultaneous connections. Periodically (1-5 times/hour) router suddenly reboots with lots of messages in consol...

Alard_626 by Level 1
  • 1810 Views
  • 6 replies
  • 0 Helpful votes

Hi,I want to upgrade my IOS on an 871W.  In order to do this I need to upgrade the memory.  I have found that I need the MEM870-32F  (Am I correct?).As in here:  http://www.ebay.com/itm/MEM870-32F-32MB-FLASH-MEMORY-CISCO-871-871W-876-877-878-/1606180...

marlzzzzz by Level 1
  • 715 Views
  • 1 replies
  • 0 Helpful votes