Hello, I am running the following configcloud -> ASA -> ROUTER -> LAN,I am doing NAT/PAT on the router instead of the ASA because I am bumping up against my 10 user license.Everything is working fine, but I am having an issue trying to get the asa to...
Hi guys I have a problem which is really giving me a headache. It is a single router with dual ISPs. It is a 2800 and there is failover configured. I have implemented object tracking and the feature works great except that lately, whenever there is a...
Hi All,I'm hoping the community can help me out with this one....I have a WAN connection to a site that is being brought into my network via MPLS. The Service Provider and my edge router is using BGP. The BGP routes are being redistributed into OSP...
Good Day Everyone,I am looking around the Cisco site for a table showing the Cisco router model number against the number of user supported.I have had a sales person ask me if an 1841 would support 20 users with the possiblility to grow to 50 and in ...
Dears ExpertsHiCould you help me to Install WAN NETWORKto PLEASEMain Office ( HQ): Cisco Integrated Service Router 2811 1 Port Channelized T1/E1 and ISDN PRI High Speed WAN Interface Card E1/GSHDSL Modems Cisco 2800 IOS firmware Branches :Cisco...
Dear all,I currently have a VWIC2-1MFT-T1/E1 card.This card does not allowed me to configure more than 2 channel-groups in my E1 port.I need to use a channelized E1 with 10 different channel-grous (10 different conections for branch offices).Ive read...
HelloWe got One ADSL 4MB Link terminated on 877, this router is the default Gateway for users. To have redundancy we plan to get another link 4MB ADSL link terminating on another 877 from a different provider. what config is needed to have auto switc...
I've inherited a 7206VXR router and it takes very long to boot. It outputs READonly ROMMON initialized to the console and 14 minutes later it continues the boot process. After 17+ minutes the boot is complete with the correct full image.The process...
Hi.I made following schema.ASA5505 + sec plus licensee0/0 -access VLAN2-> uplinke0/1 - trunk .1q -> switche0/2 - access VLAN9e0/3 - access VLAN9e0/4 - access VLAN9e0/5 - access VLAN9e0/6 - access VLAN9e0/7 - access VLAN9native VLAN was reassigned fro...
Need to configure 2 E1's for both voice and data. Also implement load balancing and QOS on them. Can someone help me to configure the E1's.These E1's are terminated on G703 card. The routing protocol is eigrp.Regards
Hi,How do I configure a data T1 serial link on a router using IOS 15 and a VWIC3-1MFT-T1/E1 module. The "interface serialx/x/x" are not there anymore?
I have a hub and spoke DMVPN setup.Each remote site has a Cisco 1861 router (latest IOS) with it's fa0/0 interface connected to an ISP supplied DSL router that is doing all the authentication for me and bridging. No QoS of any kind on the ISP router....
Greetings!I need to attach a QOS policy to a layer 2 WAN interface between two sites. This is actually an extended LAN circuit with 500Mb/s of allocated bandwidth. The interfaces are Gigabit so I want to make sure I don't attempt to transmit traf...
Hi All,i have a 7201 router with NPE-G2. i have a design which i have the option to send all the traffic through a GRE tunnel or a L2TPV3 tunnel.which method is more cpu consumption ?thanks,Avi.
I am working with a medical group that has three locations. Each location has three T1 lines bundled for data only. They will be replacing the bundled T1 lines with fiber optic. They want to have their voice moved over once the fiber is in place a...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 06-06-2025 12:18 PM | ||
| 05-28-2025 01:50 AM | ||
| 05-15-2025 07:28 AM | ||
| 05-13-2025 03:49 AM | ||
| 05-12-2025 03:28 PM |
| User | Count |
|---|---|
| 9 | |
| 4 | |
| 3 | |
| 3 | |
| 2 |
