Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Don't miss this Cisco Catalyst 8000 offer

 
Labels

Forum Posts

I'm a server guy but have taken over our networking as we are downsizing and trying to come up to speed as quickly as possible. I have a 6509 switch that routes traffic to the internet thru one provider. But have added a point to point t1(and added c...

khmay1984 by Level 1
  • 269 Views
  • 2 replies
  • 0 Helpful votes

All,I thought that the default timers for bgp were 60 and holddown was 180. I may be wrong, but shouldn't a route that falls out of the table be at most put back into the table after 180 seconds (3 min.)?We tested our failover this weekend, and we sh...

Is there any rhyme or reason to how routes are listed with a simple 'show ip route'?I notice on the 2800 series routers, they appear random. On the 6500, they are clumped together with similar IPs, but not sorted. And on the 7600, they are actually...

I'm confused about static route adjustment interval. I have two 6509's running HSRP. There are networks that are statically routed through the HSRP interface. Each 6509 has static weights assigned to each route for failover.The question I have is...

we have dual sup engines.How do we plan for an IOS upgrade with minimum or no downtime?i would like to know the steps explained in detail

aneesh.ts by Level 1
  • 2526 Views
  • 1 replies
  • 0 Helpful votes

We have a mpls setup with 6 locations.I can telnet to all routers except for one. This setup has been in place for at least 5years. I was able to telnet to all of the routers until yesterday. There was no changes made to the infrastructure and now al...

dukeminus by Level 1
  • 461 Views
  • 2 replies
  • 0 Helpful votes

Hi Experts,DO you know what is this error message?.Jun 3 00:42:27.304 GMT: %HSRP-6-STATECHANGE: GigabitEthernet0/1.2 Grp 2 state Active -> Speak.Jun 3 01:06:46.446 GMT: %HSRP-6-STATECHANGE: GigabitEthernet0/2.22 Grp 34 state Standby -> Active.Jun ...

Greetings-I currently have a 2821 running v12.4(3i) with an internal WIC-1DSU-T1-V2 module. I am increasing my internet speed from a single T1 to a 2xT1, which entails 2 RJ-45 cable handoffs from my Verizon demark. To accommodate, do I only need to...

tasete by Level 1
  • 398 Views
  • 3 replies
  • 0 Helpful votes

Hi Friends,i have dual router multihomed network from 2 different ISP and advertising just one /24 network in BGP that is acceptable from both ISPs.now i need fast convergence in BGP because if ISP-1 link goes down it takes approx 1 min. to route the...

Hi,I was asked by my client to have L2 network spread over L3. I am aware of the VPLS stuff. It will be great help if somebody can guide me to the subject line technology documentation for cisco products.The bried decription about OTV:A method and sy...

We have different 2 ISP's that are advertising each other's subnets using BGP. What would be an expected recovery time if one ISP fails for the other ISP to advertise the route through them?

Hi,HeadOffice is connecting to branch offic e via MPLS Cloud running BGP and some office connected point-2-point via Fiber.OSPF is running with P-2-P offices and BGP with MPLS.What is the best approach to accept traffic from branch-office without ser...