Rourt-Aip route 0.0.0.0 0.0.0.0 E0 ip route 192.168.11.32 S0ip route 192.168.11.64 S1ip route 192.168.11.32 S1 10ip route 192.168.11.64 S0 10Router-Bip route 0.0.0.0 0.0.0.0 S0ip route 192.168.11.0 Serial0ip route 192.168.64.0 Serial1ip route 19...
Rourt-Aip route 0.0.0.0 0.0.0.0 E0 ip route 192.168.11.32 S0ip route 192.168.11.64 S1ip route 192.168.11.32 S1 10ip route 192.168.11.64 S0 10Router-Bip route 0.0.0.0 0.0.0.0 S0ip route 192.168.11.0 Serial0ip route 192.168.64.0 Serial1ip route 19...
anyone, I've attached a diagram to give more details of the scenario. Now here's the prob., the customer using his PDA wants to access his private network via GPRS through VPN connection. The Nokia box running NAT=overloading and checkpoint firewall ...
We have a regional office with two WS-C2950G-48-EI switches, both close to fully populated. Periodically, at a frequency of 1-2 weeks, all workstations in one or the other switch (but not both at the same time) will lose all connectivity to the netwo...
I have noticed that with a 2811 router and the older WIC-1T, that a 'clock rate 2000000' command appears in the configuration. No matter what I try, the command remains. I must be missing something here. Any suggestions would be great.
Hi all,what is the size of a GRE Keepalive Packet?ThansRgdsGianluca
I was asked to configure BGP under certain requirements:AS100 (R6)will not accept any route from As 54 with network mask longer than 20. Since R6 is in AS 100, I configured R6 as following:router bgp 100 bgp log-neighbor-changes neighbor 54.1.6.254 r...
Hi,have a serial int with output queue drops increasing slowly, however the tx, rx loads appear low, its not a busy link. any idea what could be causing this?
Hello,I have spent a bit of time trying to generate enough traffic to test allocating bandwidth among egress queues on a a fa port on a 3550 switch.We have a requirement to limit the traffic over a metro ethernet LAN between two specific devices to 6...
A little background:I have 2 1400 series bridges that I want to use to connect two networks that are about 2 miles apart. I installed the bridges and everything worked fine. I can connect through the 1400 bridges to the remote network and move data ...
can i use WIC-1SHDSL (not wic-1ADSL) to make an ADSL connection to my ISP?thanks
Is't possible to set FlowControl on int FastEthernet on Cisco 3745?
I have 2 878's that I've been trying for some time to configure to use ISDN, without success unfortunately.It seems that the BRI interface is disabled on these units for dialout (dunno why), so now I'm looking into using an external ISDN TA and conne...
Hi AllI have three sites: Site A, which is the main site. The site B and C are in the same city, but different areas.B and C are each linked to A via 192K dedicated circuits, and linked to each other via a 512K dedicated circuit. This give us a triag...
We have a Cisco 3825 at our data center (Ohio) with 3xT1 in an MPPP configuration.We have a Cisco 2851 at a remote office (Texas) with 2xT1 in an MPPP configuration.We are seeing different upload and download speeds across this link. If I move a 5MB...
Hi all, If we have border router running both BGP peered with isp BGP router ..wht is the normal practice to filter out overwhelming route updates from isp router.How do we redistribute the bgp routes in to IGP?I knew that by configuring ^$ regular ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 04:13 PM | ||
08-07-2024 10:40 AM | ||
08-07-2024 02:00 AM | ||
08-05-2024 04:22 PM | ||
07-15-2024 05:07 AM |
User | Count |
---|---|
13 | |
8 | |
7 | |
5 | |
4 |