I have an router 7500 and deleted bootflash.now, the router only enter in rommon and it has not option for copy the bootflhas for ftpt server.. how do i recover el boot ?
I have an router 7500 and deleted bootflash.now, the router only enter in rommon and it has not option for copy the bootflhas for ftpt server.. how do i recover el boot ?
Hello, I was wondering if you can help me with my NAT config, because I have 2 T1's in each serial interface, BUT only one of the serial interfaces is working properly. here is my running config thank you so muchI'LL be waiting your answer... Thanks!...
Hi,Given the below scenario+++++++++++++++++++++++++dexter#show ip eigrp topology all-links IP-EIGRP Topology Table for AS(1)/ID(192.168.0.200)Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P ...
Hello. Does anyone know if there's a maximum file size supported on the 256 MB compact flash cards that go with the ISR routers?I've been trying to upload some newer code on my routers and whenever the transfer hits 33,546,240 bytes the transfer sto...
Hello,I wan't to setup my cisco 877 adsl router but it fails to initiate ATM.Here is some output:*Mar 1 00:33:44.643: DSL: Send ADSL_OPEN command.*Mar 1 00:33:44.643: DSL(ATM0): Using subfunction 0x0*Mar 1 00:33:44.643: LOCAL:Max noise margin for pow...
is any difference between "ip cef" & "ip load-sharing per-packet" ?
Hello,How to enable (command) the egress and ingress filtering in the interfaces in the Router?.Quick response is appreciated.Rgds,Raju
we have one central router of 3600 series.our remote offices are connected to this router through ISDN.PRI is terminated in the central router and BRI at remote location.Remote routers dial to central router. Now, i want that only central router shou...
We have a 10 Mbps link on ethernet and a 2 Mbps on serial. we wish to have unequal load balancing.the sh ip eigrp topo result is via 10.254.2.66 (30720/28160), FastEthernet0/1via 10.254.2.54 (1764352/28160), Serial0/1and the link details are,BW 10000...
I have an ipsec tunnel created between a 1841 and 871. I have vlan1 as 10.1.5.1 on the 871 and 10.1.4,10.1.3, and 10.1.2 on the 1841. I cannot ping from each router to any destination lan ip. I do not know how to add a static route to make these w...
Currently have a 2600 router with serial interface connected to external Adtran CSU/DSU on a frame relay WAN.Purchased a WIC-1DSU-T1 interface module and would like to know how to configure it. (so I don't have to hire our router consultant...yet)Her...
Does anyone know where I can find any basic step by step configuration docs for configuring QOS on Routers and switches.thanks
I am switching over from 2600 serier to a new 2821 so that I may have 4 T1's data only (no voice). On the old 2600 a T1 was configured as such:interface Serial0/0 description Wherever ip address 10.201.254.1 255.255.255.0 no ip directed-broadcast no ...
Hello All:Is there anyway to limit the use of outbound bandwidth by protocol. Would appreciate any help or point me an article that covers this topic,Thanks in advance
I am trying to use the Cisco SDM to configure a site-to-site vpn for an 1841 on a T1 directly to a 871 on Cable. As SOON as I save the quick configuration on one of the routers, the pinging ability immediately goes down between the two. But, I can ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-22-2024 02:54 AM | ||
07-15-2024 05:07 AM | ||
07-13-2024 09:04 AM | ||
07-09-2024 05:41 AM | ||
07-03-2024 08:54 PM |
User | Count |
---|---|
16 | |
5 | |
4 | |
4 | |
3 |