Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Bookmark
|
Subscribe
|

Labels

Forum Posts

Please look at my configuration:R7#sh runBuilding configuration...Current configuration:!! Last configuration change at 17:52:58 UTC Tue Apr 13 1993! NVRAM config last updated at 17:50:34 UTC Tue Apr 13 1993!version 12.1service timestamps debug uptim...

I have 2 routers running BGP:R7 config~~~~~~~~~~~~~~~~~~~~~~~~~~~router bgp 700 redistribute connected route-map t1 neighbor 20.20.20.5 remote-as 500 neighbor 20.20.20.5 send-communityroute-map t1 permit 10 set community no-export~~~~~~~~~~~~~~~~~but...

hi;I have a FTP server behind NAT enabled Cisco router.I want to access FTP server from outside, with configuration below, when I tried to connect FTP server, from netstat command output on FTP server I see there is a connection to FTP port but wait ...

Hi , please anyone tell me the meanings of these alrams which are coming in my MGX 8850 M8850_SF.10.MPSM155[FR].a > dsplnalmcnt 1.1 Line Number: 1.1 Elapsed Time(in sec): 397 Num of LOS : 0 Num of OOF : 0 Num of RAI : 0 ...

cisco by Level 1
  • 638 Views
  • 2 replies
  • 0 Helpful votes

HiI have a 3745 router with CE Modulewhen I start power on , then after the message the router not boot. same result arise after without CE module also.so what is the problem ?. --------------------Bootstrap version 12.2 (8r)T2program load complete, ...

iqbalkhan by Level 1
  • 553 Views
  • 5 replies
  • 0 Helpful votes

Hi guys,just need to sort out the amount of adjacencies created on the same LAN segment in my understanding.What I need to understand correctly is thisSay we have 5 routers without the DR/BDRm I calculate n(n-1) where n is the number of routers, woul...

tjskier69 by Level 1
  • 1219 Views
  • 3 replies
  • 0 Helpful votes

Amateur here. I'm pre-configuring two routers (1721 WIC-DSU-T1 - 7204's PA-MC-4T1) prior to shipping to remote location for a full T1. getting an alarm on WIC-1DSU-T1 and no LED on Port on the 7204. What are the most common causes? Saw related email ...

Resolved! route-map problem

I have 2 routers with the folowing config:hostname R5interface Ethernet0 ip address 10.10.10.1 255.255.255.0 router bgp 500 bgp log-neighbor-changes neighbor 10.10.10.2 remote-as 700 neighbor 10.10.10.2 route-map block7 in neighbor 20.20.20.1 remo...

hi, Have a look at attachment,there is a 2950 24 port switch , which is connected to 8274 ibm core switch via ethernet.The 2950 has two fibre modules connected to 4507 switch with hsrp and etherchannel configured.The 2950 switch ethernet link conn...

I have seen in many cases while troubleshooting Application accessibility issues, when we clear the NAT translations on the Router applications start working. How does this help?

i have a cisco 871w with two ssids configured. one for my private network, and one for the guest network. is there a way i can keep wireless clients from associating with the ssid for the private network? if your mac isn't specified in one of the ...

Resolved! BGP confusion

Hi all,I was helped yesterday with some routing protocol issues. going to an mpls network that will only allow BPG or static. I found a BGP config in this group but just wanted some clarification as i am new to the BGP world. setup as follows:inter...

rhltechie by Level 1
  • 717 Views
  • 7 replies
  • 0 Helpful votes