hi,i have got 2 (1+1) links to the same location configured on seperate routers.i need to do load sharing on traffic through them .could anyone send me the config ...how to make it work.and which is the best way glbp or mmlp.Thanks in advance
Fairly new to Cisco IOS, etc. but I have a new 1811W that I would like to hook up to two different ISPs and have (preferably) load balanced traffic or at least active/passive failover of traffic. Any sample configs that someone could share?Thanks,Tar...
I 'm currently prepare BSCI.When ip route point to interface ethernet (broadcast interface) is used ? Example: ip route 192.168.1.0 255.255.255.0 eth0When route ip policy map can be assign to loopback interface ?Best regards
Can anyone pls help ,i`ve got a Cisco 3745 with a remote site connected to it via Diginet ,i have configured a static route on the router ,problem is when interface to remote site drops the route dissapears from the routing table and causes a routing...
I have two 2950c-24 Switches connected together via a crossover cable on port 24 on both switches. On one switch someone has configured Port 24 with trunking but on the other switch, there is no configuration on port 24 at all. With this type of co...
I have a 2600 and 3700 router with a 4-port ATM IMA card. I have 2 T1s on each router forming an IMA group. My users are experiencing with slow reponsiveness. When I issued the command "show atm interface atm1/ima0" on each router, I noticed the f...
Hi All,Can anybody explain to me why the NAT TCP translation timeout default is 86400 seconds (1 day). I am running NAT overload and most of the time my NAT space gets filled over with lot of translations. I want to know the appropriate TCP fine tuni...
We have 32 static IP from our ISP.All of these are NAT 1-->1 from FastEthernet 0/1 to FastEthernet 0/0. However, now we need to have one of the static IP's to many (NAT 1-->many) from FastEthernet 0/1 to FastEthernet 1/0.Currently 1-1 NAT is done by:...
Hi guys, I appear to having a lot of issues qwith 877's. This paticular one is really annoying. If anyone could help i would appreciate it. I setup one 877 on a hub site with the SDM standard DMVPN setup. This works fine. i went to the remote site an...
maybe someone knows:Is there a comand available like the "sh idprom interface" to collect the S/N of the GBICs inserted for Catalyst 3550 switches running IOS 12.1.We use it with Cat6k5 and Cat4k5, but with 3550 this command won't work.Thanks!
Hello All. I just got my hands on a Cisco 837 router and was wondering if I could get assistance in configuring the device to work with my cable internet account. I need assistance in understanding how to set the E1 (wan connection to assign it sel...
I have little experience with a CAT5500 switch. I have one in Ciscoworks that fails when I try to retrieve inventory or sync archive. I get the following message:CM0151 PRIMARY RUNNING Config fetch failed for Catalyst5500 Cause: Failed to get the sta...
Hi everybody,Does anybody in this forum have an idea as to what the maximum amount of nodes is in a DPT OC48 ring? According to the Cisco website the maximum amount of nodes is 128 (assuming that only Rev-B cards are installed in the ring) but I woul...
A server administrator is complaining that his server is receiving excessive multicast traffic, the server is currently connected to a WS-C2950G-48-EI Version 12.1(13)EA1. Is there any way of restricting multicast traffic received on the interface t...
Hello Netpro,I discovered an interface called "NVI0" on an 2610xm running with IOS "c2600-spservicesk9-mz.123-14.T3.bin"I wasn't able to find any documentation about this interface type, does anyone know what this interface is about?It doesn't show ...
