Hello all,Please reference the image for convenience. R1 and R2 are our routers running ebgp with two isp R3 and R4 which are sending default routes towards us.R1 and R2 are ibgp peers also sending default route to each other also running vrrp.R5 is...
Forum Posts
Resolved! 800/1900 router encryption
Hi there, Thanks for reading. I'm wondering what the upper limits as far as bandwidth for tunnel traffic on 800 series routers. Will they support a 50Mbps circuit connection? Thanks again, Bob
The L3 tunnel is up and works great. Now I'm testing it with my local ISP services and I'm trying to manage the remote ASA through the tunnel. I can ping/ssh from PC to PC through the tunnel (192.168.168.140 <-> 192.168.180.4) but I can't ping/ssh ...
Hello all. I was wondering if you ca help. I am trying to run a capture on our WAN interface for a certain IP. Every time I try to execute the command I receive "EPC configuration not permitted on standby" ROPS-M0-A2-2-4500X-VSS#monitor capture MYC...
Im building an ASR 1001X, and I see so many versions of software !! Denali 16.3.5 (MD), vs Everest 16.6.2(ED), vs Fuji 16.7.1 (ED) .. Anyone knows what the difference is ? and which is the stable version that I should go with ? I couldnt find any c...
Hi all, I have a pair of 4400s setup specifically for SIP voice services. In our config we have an 'outside' public IP connecting to the carrier voice cloud, and a 'inside' IP connecting to my private IP network. Since i have two 4400s we wanted to...
Hello to the community. I have this topology: The green devices are switches layer 2, the blue devices are switches layer 3. I use the VLAN250 as transit network, the green devices has only the vlan250 (L2) permitted on every trunk: SWT-A: rou...
Hello, I have upgraded route reflector in private MPLS network from IOS XE 3.16.5 to Everest 16.6.5 release. After upgrade, dynamic BGP peers did not connect to RR. In debug, I see mesaages such as: 004668: Mar 10 02:07:02.382 MET: BGP:DN: peer-gro...
Resolved! BGP flowspec SNMP counters
Hello, Does anyone know if IOSXR on ASR9K supports SNMP counters for BGP flowspec announces ? All I want to do is to retrieve the counters using SNMP. cf: RP/0/RSP0/CPU0:XXX#show flowspec afi-all detail Wed Mar 6 10:55:53.481 CET AFI: IPv4 Flow ...
Resolved! VRF-LITE and DMVPN
Hi there. I am trying to configure a DMVPN overlay and want to create multiple VRFs in this overlay. On the hub router are all the tunnels terminated on the same interface in Global Routing but with different network-ids. But when I try and get...
Hi any one can help ne to know what is this error at the Log and if it will impact the service Mar 4 10:59:03.138: %SIGNATURE-3-NOT_ABLE_TO_PROCESS: %ERROR: Not able to process Signature in disk2:!P!N@pA55. Mar 4 12:09:38.470: %SIGNATURE-3-...
Hello - It is a general question to know how to determine the model of the Router based on the WAN Internet link i am going to connect. Reading the article http://www.anticisco.ru/pubs/ISR_G2_Perfomance.pdf and other datasheet it is mentioned about ...
Hello, I've been trying to establish a Route-Reflector for an MPLS VPN, and was hoping to use dynamic neighbors to reduce the configuration complexity and ease the change burden while adding new PE routers. My BGP config on the Route Reflector is...
Want to know if there is the possibility of reading VSWR on the antennae on IR800 LTE and whether it is possible to set up alarm for bad or cracked antennae cable Are there some SNMP MIBs I can use for this ?
Hi I am working on migrating my P2P network to MPLS with dual Service provider.Each location will have dual router connecting each Service Provider in active-active state,I am looking for solution where I can route traffic base on Application port. e...
