This is very high level, wanting to know if this is possible. We're the middle man. I don't have access to or knowledge of equipment or configs on the other providers. Currently we are handed off a GRE tunnel to a router. We have an ipsec tunnel ...
The content you are looking for has been archived. View related content below.
This is very high level, wanting to know if this is possible. We're the middle man. I don't have access to or knowledge of equipment or configs on the other providers. Currently we are handed off a GRE tunnel to a router. We have an ipsec tunnel ...
Hi, I have a ISR1100 (C1111) with two connections: fiber (GiE0/0/0) and LTE (Cellular0/2/0). Config excerpt:ip route 0.0.0.0 0.0.0.0 100.64.107.1 name primary track 1ip route 0.0.0.0 0.0.0.0 Cellular0/2/0 10 name backup!ip sla 1icmp-echo 8.8.8.8 sour...
I am setting up a C1111-8PWA-WS for the first time. After not being able access the internal wireless card I decided to set up without it. I have a Cisco SG350-28P switch that has POE for the AP's. Trying to set up the basic unit with just the rou...
We have a FlexVPN Setup where Spoke2Spoke connections get created dynamically with the help of virtual access interfaces. So if i want to edit something within a virtual-template, i get the error that it is locked:router(config)#interface Virtual-Tem...
je trouve cette output anormal, que pensez vous SVP de l'état ospf dasn ce cas :O E1 10.232.51.3/32 [110/53] via 10.4.151.2, 12:16:54, Port-channel20.1017[110/53] via 10.4.151.2, 12:16:48, Port-channel20.1017[110/53] via 10.4.151.2, 12:16:54, Port-ch...
Hi.I have one Cisco ISR 4321. This is a brand new router and I am the first owner.I have encountered the following fault since the first start up:It keeps restarting at random intervals. Sometimes after 10 minutes but sometimes it lasts for 2 hours.T...
Hello Everyone I have to set up an ipsec tunnel with Lo0 as source of tha tunnel. Nat is activated in My CE and in the ISP level (NAT444)All ipsec and Nat configuration is ok but, and as I know that for the NAT to work correctly, the packet should pa...
Hi Experts,Today when I am learning our company's routers configuration, I found that a Port-channel is in L3 and it is in VLAN490 as below:interface Port-channel1.490 description To_CP01 encapsulation dot1Q 490 ip flow monitor NETFLOW_MON input ...
Hi,we are using the Cisco ASR1001-X as core router on our ISP network. For the management of the CPE I set up a TR-069 ACS server. For testing purposes I configured the ACS URL manually on the CPE, which works fine.However I'd like our ASR to pass th...
I tried ctrl + Crommon 1> confreg 0x2142rommon 2> resetbut he didn't accept the reset the i restart the router with power button then i found router suck in below could any one help me how to solve this issue i restaert the router 2 time using powe...
From where to download the cisco images (Router and L2,L3 switches) for eve ng and which image will work good.Below is the list mentioned in eve ng but what is the proper way to download these imagesDynamips (Cisco IOS emulation)c7200-adventerprisek9...
I have a setup in which i have 2 routers connected to same ISP A both via default route pointing towards ISP for internet.Now we want to add another ISP B on both routers however that ISP will use BGP with RIPE IP address over the internet.Now we wan...
Hello Team,I have a topology as below;I have point to point connections to multiple partners who have different unique prefixes - to avoid overlapping of subnets.They need to access my internal resources - in this case vlan 50 and 70 for respective s...
Please refer the below topology,Client >>> Cisco router >>> Firewall >>> Upstream device >>> serverI have set mtu as 200 in my upstream device and as exepected when client access the server(http) the packets are fragmented.However when I set tcp-ms...
I tested the ASA 5520 iperf3 to check its performance. I then wanted to add NAT to it to find out how much it was taxing the device. However, I kept having the problem that almost all traffic was untranslated.The created objects are the same, i.e. 19...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 10:40 AM | ||
07-15-2024 05:07 AM | ||
07-13-2024 09:04 AM | ||
07-09-2024 05:41 AM | ||
07-03-2024 08:54 PM |
User | Count |
---|---|
10 | |
8 | |
7 | |
4 | |
3 |