We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
Hello,Anyone knows the default password?Thanks,
Hello, I am trying to set up a switch to carry two different subnets (.10 and .20), with each on their own VLAN to avoid any contact between the two. Each VLAN is being carried in on its own ethernet cable, to ports 11 and 12, respectively. Individu...
hello I'm Harry I'm korean so I'm not good at speaking in English. Anyway I have some questions about sg300 I want to ping from valn1 to other vlan's without a router.As far as I'm concernd, normally switch can use a "ip routeing"commend but I can't ...
Resolved! did I brick my SF300-08?
I got assigned to manage a rack that includes a Cisco SF300-08. It was working fine. I needed to login to it, but the previous admin did not leave the user/pass for the switch. The defaults of "cisco/cisco" didn't work. So I looked up how to ...
Hi Team I have been asked to configure Cisco SG500 switch with initial setup. I did complete the configurations except for stack ip address. Need support how to configure stack ip address to switch. Thanks Srinivas Patnaik
I have a SG110-24HP-NA unmanaged switch, purchased used cisco IP phones model #7960 and am trying to get the phones working. I have charter as my internet provider using a Arris TM804G modem. Phones are not working, what am I missing?
Hi there. I have Cisco SG500 in L3 mode. Now I need to get ip addresses for vlans from two different external dhcp servers (for ex. 192.168.1.21 and 10.17.10.10). For Cisco Catalyst it would looks something like this: int vlan 100 ip addr 10.100...
Hello.I bought the SG200 switch and the Sg300-10 switch.It supports POE.Of course I have enabled jumbo frames in the port settings.(on the Web)But my GiGe camera does not get good images.It works very well when i replace it with a Netgea...
Hi all! How do I delete Vlan DB on sg300-28 ? Note: The Startup-config file was already deleted from flash
Hi , Can you provide me firmware for (SG300-28P 28-Port Gigabit PoE Managed Switch ). because when i upload any firmware (.ros) i get error message "Copy: Illegal software format" am facing many problems with current firmware "1.3.0.62 ". thanks
Hello! Is there some overview of the power consumption for the new SG250X-48P available?I am interested in some load scenario (idle, 1p conn., 1p poe conn., ..). Data sheet tells ~70W for system, thats for idle, or max. load w/o poe? Hope someone c...
Hi - was wondering if anyone else has seen this problem - recently installed two SG220-26 switches; 4 separate LACP port channel groups were configured - #1 - 2 port LACP port channel group to a second SG220-26 #2 - 4 port LACP port channel group t...
The sg300 can have up to eight network pools.Is there a Small Business Switches with more than 8 network pools?
HiCan we use 4 SFP ports as UPlink ports on SG500 switch or 2 ports as SFP and 2 ports as stacking for SG500 .please suggest.Thanks and RegardsLakshman Kumar S
Folks, I've enabled DHCP Server on my SG-300 and it leases IP addresses fine. The issue is the default router setting which I haven't configured/enabled that in my setting, but DHCP client gets default router IP address as well. Since the client ha...
