Hi,Dear Sir/Madam,
we configured VPC under 7K, and using otv connect to two site
recently we upgrade software and reload one by one for 4 netxus 7K ,and found some problems.
for example
If we reload nexus7k-1, and check log on n...
Dear all,
We have an asa5525x series and 2 CISCO 10Gb switch SAG350XG-2F10,
problem in our enviroment is that new servers get apipa, we solve this by edit the register and add the dword ArpRetryCount
Problem is that we have a deep sec DSVA in our vm...
Hi,I have a pair of Cisco 4507 switches in VSS mode. An server (10.4.1.166) using Microsoft NLB MAC address (03bf.0a04.01a6) is connected to VSS Node 1 on port Gi1/6/43. The following is configured on the switch.arp 10.4.1.166 03bf.0a04.01a6 ARPAmac...
Hi Sirs
My draft architecture
PC1(192.168.11.2/24)<=>F0/1(192.168.11.1/24)(2811R1)F0/0(192.168.1.1/24)<=>F0/0(192.168.1.2/24)(2811R2)F0/1(192.168.13.1/24)<=>PC2(192.168.13.2/24)
config Static routing
2811R1: ip route 192.168.13.0 255.255.255.0 192....
Hi All
I brought Nexus 9300 with 96p 1/10G-T and 6p 40G QSFP N9K-C93120TX . I have a problem which is randomly some port or ports will stop working or blinking till i restart the switch. I was using normal 1gb switch 48ports and i had zero problems...
Hello,
I have a Cisco 1941 with some DHCP scopes on it and I need to add option 43 to them so they can locate our Cisco Wireless LAN Controller using CAPWAP, has anyone done this before?
WLC = 192.168.0.110
My router DHCP is:
ip dhcp pool vlan20 ...
Hello
I have a Firewall with a DMPVN Router in an DMZ. The VPN`s a working without any problem but the NAT on the Firewall did not.
So the LAN from the Firewall and Router are connected and i have eigrp running.
When i insert the IP as Gateway of ...
Hi,
I have redundant networks paths for HR-SWI-01, shown in the image attached, the black color (path 1) and green color (path 2) lines.
When both of the paths are enabled MULTICAST traffic travels from HR-SWI-01 through LA-SWI-02 to F-SWI-01 and c...
Dears,
I have 100 switches in my network
In every switch i have Admin username and password.
My username is "Admin"
Password is "@dmin@d205"
Enable password "@dmin@502
But my requirement
My manager said that for another user who can onl...
Hi,
I am having 200 number of cisco switch in my network, I want details like host name/IP address of the device (PC, Printer, Laptop) connected cisco switch. Can any one help me?
Dears
I have 5 department
1-HR
2-SALES
3-Customer service
4-IT
5-Planning Department
My IP class is B and my range is 172.141.0.0/16
My requirement is
I will assign IP for "HR" only 172.141.10.0/16 range
IP for "SALES" only 172.141.20.0/16 range
IP f...
Hello Community,
I hope this is the right category :)
Right now I am building a network for a project and for some reason my DHCP server does not work.
For a quick overview:I have: 1x client (who should recieve a ip address)1x Layer 3 switch1x router...
Hey guys,I followed no ips' configuration guide
on my Cisco 1921 which is using the IOS version 155-3.M4a.bin. I am unable to get any updates. I have enabled debug, but its not showing anything. Can you please help. I can browse the internet through...
Folks,
I am looking for a solution where I can create a VLAN with a ip helper-address only. i.e. this VLAN will not have any L3 address associated to it.The reason is that we do not want to use this switch as the gateway.
Or else can I use a configu...
