Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Dears, I'm having issue on MAC filtering on cisco 2960 SW. Macbook laptop is not working in MAC filtering. My setup is Wireless AP is connected to trunk port and AP is broadcasting 3 SSID(different vlans). I apply MAC filtering on trunk port but th...

Hi! I have a branch new Cisco ASR 1002-X but in the first time power on, it showed an error as below and then stopped booting so how can I do now? thanks! Located Software/asr1002x-universalk9.03.16.02.S.155-3.S2-ext.SPA.bin, start cluster is 220524...

Hi all, is there any way to filter cdp throught acces ports on catalyst switches? We have virus on site which is searching for other devices throught CDP protocol or Mikrotic neighbour. If i block - MAC Protocol 800 ,packet type Boadcast in mikroti...

hi All, I have two cisco Switches Connected through IPvpn Datalink in two sites, the problem that the two switches are in default configuration All interface trunk Untagged. but not all the hosts can reach each other through the data link, for examp...

Hi  I am facing the following massages at my device. May 10 02:00:39.793: %SW_MATM-4-MACFLAP_NOTIF: Host 0090.e846.98ee in vlan 105 is flapping between port Gi0/23 and port Gi0/4 As per my understanding there is some issue in VLAN 105 not at physica...

Not sure if this is the correct community to be posting this, but here goes. I need to see if I can disable the following UDP ports on my Cisco 3850 switches. UDP ports: 5246, 5247, 6352, 12124,12125,12134,12135,12222,12223,16666,16667,16668 From ...

Hi all, I am getting the following error when I tried to downgrade the IOS on a cat4510R+E: rommon 3 >boot bootflash:cat4500e-universalk9.SPA.03.04.01.SG.151-2.SG1.binLoading image !!!!!!!!!!!!!!!!!!!!!! Checking digital signature.... Verification F...

I was reading campus design guide and comparing the interconnect of switches and came with this question: When we have two or three tier design for campas lan where we have Access, Distribution and and core layers. How to interconnect the layers with...

inamprix1 by Level 1
  • 809 Views
  • 1 replies
  • 0 Helpful votes

Hi all, I have my Nexus 7000 and I will create 3 vdc (core, aggregation, otv) I would like to know if there’s any best practices to interconnect this vdc contexts. thanks. 452

I have a 3850 stack with 2 members.  The master died and switch 2 took over.  As you can see below, it's waiting on switch 1.  I have it ready to configure, but I need some advice on how to proceed.  I'd like the current configuration to remain, will...

Hi everyone, In the attached digram R4 in AS 30 seems to have two paths to 75.1.0.1/16 and 75.2.0.1/16 (on R7), one is through R6 and the other one is through R2 -> R1 -> R3 -> R5. But the following on R4 only shows there is one path? I am expecting ...

Hi Guys! A customer needs to put Switches with DC Power Suplies in their energy sub stations. I was thinking about maybe a Catalyst 2960 and a XPS-2000 or Cisco Industrial Ethernet Series Switches. What do you think or recommend for this stage? The c...

sisely_pv by Level 1
  • 3653 Views
  • 1 replies
  • 0 Helpful votes