HelloCurrently we have a stack of 7 9300 switches in a client site.While troubleshooting some stuff i notice that the uptime on one of the members is showing up as unknown: Switch 05---------Switch uptime : UnknownBase Ethernet MAC Address : 70:35:09...
Forum Posts
Hi all, Just want confirmation with this, is this really hardware issue based on the log was given?The SW cannot be detected by the chassis. SPMY-3A-IDF1#show module Mod Ports Card Type Model Serial No. --- -...
Hi all, I have issue with customer that said the module was faulty. Below is the error log that i received. 2021 Jan 3 09:01:49 SPMY-N7K-B-CORE %PLATFORM-2-MOD_DETECT: Module 10 detected (Serial number JAF1424CAHJ) Module-Type 10 Gbps Ethernet Modul...
I was upgrading some 55A2s in lab this morning and got stuck for a while in a sysadmin console position, instead of the router ios mode that I usually use. I realize these are like VMs on a device, but my knowledge of how to use them, and more import...
I am running a simple closed AoIP network on two Cisco SG300 switches. I have two VLANs. One for the Dante AoIP stream (192.168.0.xxx) and one for various controllers, CCTV, remote (iPad) control, etc. (192.200.0.xxx) I have the Front of House (FOH...
I would like to check the feasibility of using HSRP between 3 Cisco devices ?Is it technically feasible to have 3 L3 devices to be part of the same HSRP ?Attached is the diagram for reference.VLAN 141 is available in Router#1, Router#2 & Layer 3 swit...
Jan 1 11:03:06 sw.local 482: Jan 1 11:02:53: %SEC_LOGIN-5-LOGIN_SUCCESS: Login Success [user: admin] [Source: 172.16.10.2] [localport: 22] at 11:02:53 EST5EDT Fri Jan 1 2021 Switch: 3560xIOS: 15.2 Why does syslog have three dates? The first date is t...
In packet tracer, I am trying to setup multiple ssid's on a WLC, each on its own vlan. I would like clients to be able to connect to the ap's and get a dhcp address for the ssid they connect to. So far, I can only get clients to get a dhcp address ...
Hi,I've two n3500 connected and running 4 x ESX Hosts (6.5) via vPC trunk without issues - the hosts are reachable from both switches and from other networks - the vmkernel uses the mac from old network card, not the one connected to n3500 and the ma...
Resolved! CBS350 - One directional ACLs
Dear Cisco Community,I have two VLANs on my CBS350-24T-4XVLAN 10 - 192.168.10.0VLAN 30 - 192.168.30.0And I want VLAN 10 to access VLAN 30but I want to block VLAN 30 accessing VLAN 10.VLAN 10 -----ALLOW---->>> VLAN 30VLAN 10 <<<----BLOCK----- VLAN 30 ...
Sorry if this is long winded, network audio is all new to me. I need to configure an IGMP snooping querier for multicast AES67 and Q-LAN traffic across my campus network. There are several QSC cores spread throughout the network and some FlexIO devi...
I have a 9500-32C and a QSFP-4SFP25G cable. I need to connect a 10G device. Is it possible to configure this cable down to 10G or do I need the 10G specific cable?
Resolved! service-policy on Port Channel
Hello, I have a WS-C3850-48T with a Port channel comprised of four physical interfaces. If I want to apply a service-policy to this (which detects and marks certain traffic as 'EF'),. Do I simply put it on the Port Channel interface and would I put ...
Hello,Is it mandatory to declare a licence inside the HTTPS interface for a Cisco 9200L ?What are the impacts if no licence is declared ?Regards
Resolved! Cisco 9200L : too much noise
Hello,Is there any configuration (https or commande line) to reduce the speed of all the FANS inside the 9200L ?(If I compare with the 2960-X ...too much noise)Regards
