Activity in Technology and Support
Issue after upgrading to 15
After upgrading to 15 we are getting this error when we search the devices
Firewall Migration Tool not working
I want to migrate ASA 5515 to FTD2120, and I downloaded the Migration tools from Cisco version 7.7, but I have an issue as shown in the image below, after signing in using CCO, I tried with different computer same issue
Calculation of MST cost
Hi all, Could someone please explain to me why I see the things I do with MST? I have the below setup in a lab, where SW1 is configured with the lowest Cost and is the root bridge. Everything is working as expect, in regards to STP, and SW4 is Blocki...
Cisco 2802i ME - Managing 3702i and 2802i Subordinate APs
Hello, everyone.I have been recently researching about WLCs and wanted to get started with one. Currently, I was thinking on implementing a WLC via Mobility Express on my 2802i access point, with it able to manage a 3702i and a 2802i, both running li...
Need help with MPLS TE Tunnel
Working on the following topology.MPLS TE Tunnel on PE1 is successfuly configured.but I cannot reach CustomerB from PE1. The control plane information seems to be ok but I am not sure if the data plane is broken. Any help is appreciated.
Certificate-based Authentication and the Importance of AD UPN
Within Active Directory, each user account has two types of logon credentials available for authentication: Pre-Windows 2000 User Logon Name (sAMAccountName): For example, domain\User1User Logon Name (userPrincipalName or UPN): For example, User1@do...
Resolved! DHCP issue
Hey I'm new here and I had a quick question, I have this practice lab I've been working on and i can't seem to get end devices in my VLANs to get IPs from the DHCP server. I tried everything, checking to make sure routing is enabled (it is), checked ...
Cisco 9300-48U with Cisco ISE for wired 802.1x
I am trying to troubleshoot/investigate this issue and it does not seem to be making any sense to me.I have a Nexus C9300-48U version (Version 17.9.2r CAT9K_IOSXE). The switch is configured to talk to 3 Cisco ISE PSN nodes, node1, node2, and node3 (...
Vlan Change Detection
Hello,As part of our endpoints getting full access, they first go into a limited network VLANs. Only once posture is passed do we move them into a vlan with full network access. Computers have been doing this no problem for some time. Yesterday we...
Cisco 4300 ISR4331/K9 Hardware Failure
Good Day,i have a Cisco 4300 ISR4331/K9 Hardware Failure. recently i saw that the ISC light is a solid amber lightRunning the show platform command, i see this0/4 PVDM4-32 booting 00:00:17: %SPA_OIR-3-RECOVERY_RELOAD: subslot 0/4: Attempting recovery...
Finesse agents are intermittently loosing the connection to CCX
Dear team,We are facing issue intermittently raise with the ccx agents while they are logged in finesse , they lost the connection to the CCX server. This usually happened when they are exploring different applications like outlook and reverted back ...
Closed Hours Handler Issue with CUC
Hello everyone, I'm trying to configure a personalized message for holidays and days off for a specific standard extension 1001. After attempting to configure this, all calls are connected to the personalized message after the 20-second ring, regardl...
AP Heartbeat packets to the WLC
Hello, everyone. To keep the question short, an AP will periodically send heartbeat messages every 30 seconds to the WLC it associated to in order to determine whether its still alive and kicking. Here is where my confusion comes: Official Cert Guide...
Remote Access: Realm "Discovered Identities" using SAML
Hello,I have set up a FTD managed by cdFMC for remote access VPN. For authentication I use SAML with Azure AD as an IdP. The authentication itself is working fine, but the user identity of the session viewed in FMC has "Discovered Identities" as it's...
Umbrella SIG protection for Server
Is there a way to configure a proxy from Umbrella SIG on a server station to provide internet access and to be protected by Umbrella? Currently, our setup uses a tunnel from the network device to Umbrella.
| User | Helpful Count |
|---|---|
| 87 | |
| 68 | |
| 54 | |
| 53 | |
| 52 |
