Activity in Technology and Support
Resolved! Choice between Routed Access Network and switching Network L2
Hello Support,I have a LAN with a Distribution switch 9300 and Access switch 9200. 9200 series support L3 routing, my question is about implementing L2 network with Trunk or implementing routed access Network with OSPF. which is the best architecture...
Mobility tunnel beaks after HA switchover of anchor
WIth C9800-L-F-K9 model, i have a Anchor and foreign setup with mobility tunnel formed between them. It is observed that if i switchover anchor WLC (HA-SSO), the mobility tunnel does not come up. I tried changing mobility mac to static.the WMI gatewa...
Cisco D9036 modular encoder
Hi,I bought a D9036 from ebay, I found it's managment IP address and was able to open the browser but I don't know the username and password, is there any way to factory default this unit or reset the username and password, your help is appreciated.T...
meraki-org-sandbox is not available
meraki-org-sandbox environment has not be available for this week. I would like if It will be avialabe again. Thanks.
WS-C2960-48PST-S installed new iOS now it’s hung up
Hello guys,C2960 installed new iOS now it’s hung up Switch is WS-C2960-48PST-Sit used to have iOSFash:/c2960-lanlitek9-nz.122-50.SE4/c2960-lanlitek9-mz-122-50.SE4.bin"now I installed iOS"Flash:c2960-1anlitek9-mz.152-7.E12"from the picture I’m attachi...
NCS-5501-SE erros is 'DPA_QOSEA' detected the 'warning' condition
version is ncs5500-xr-7.1.2 version=7.1.2 Mon Nov 3 05:46:46.878 UTCNode Type State Config state--------------------------------------------------------------------------------0/RP0/CPU0 NCS-5501-SE(Active) IOS XR RUN NSHUT0/RP0/NPU0 Slice UP0/FT0 NC...
vManage API /attachfeature returns HTTP 400 – Unable to update device
Hello everyone, I’m encountering an issue when trying to update device template variables via the vManage REST API.The API consistently returns an HTTP 400 Bad Request, even though the workflow follows Cisco’s documented process and mirrors the web U...
4k PTZ camera refresh rate
Hi, We want to install 3x 4k PTZ's in our large conference space, I'd like to know if the resolution/refresh rate can be modified beyond the options of 30hz or 60hz.Powerline frequency in Australia is 50hz, thus the LED screen that's built in runs at...
Looking for best solution for wireless connection
Hey all. I work in a warehouse and we have 18 APs all connected to an AIR-CT3504-K9 controller. We have one spot within our warehouse where we have some PCs that are between a modular office and the bathrooms. The ceiling is really high up (maybe ...
Cisco 4321 || %IOSXEBOOT-1-INVALID_IMAGE: (RP/0) Err when loading IOS
Hello Cisco Community,The router Cisco 4321 gets stuck when trying to load IOS : isr4300-universalk9.17.06.05.SPA.bin and get the following error:%IOSXEBOOT-1-INVALID_IMAGE: (RP/0): Incompatible hardware and software image version; newer software ver...
Resolved! Migration from Cisco C9120AXI-S EWC to Cisco Catalyst CW9800 controlle
Hi All, I am planning to migrate from Cisco C9120AXI-S EWC to Cisco Catalyst CW9800 controller. Is there any updated and accurate procudure to do that ? Total AP is 5. If you recently the same thing before, please share with me. Thank you.
Cisco ISE - Intune Integration
I'm try to integrate Cisco ISE to Intune with following this article, and i got this error. Anyone know why? How to: Integrate Cisco ISE MDM with Microsoft Intune - Cisco Community
Need to configure restriction for non compliant wireless user in ise
We have FortiGate WLC for wireless user . After posture scanning if the user is non-compliant we are unable to restrict the access user is getting full access. We tried from ISE to Push ACL still the restriction is not working. Wireless user connecti...
vPC
Can somebody please explain me the vpc concept.
How to do a password reset on an FMCv300
Is there a way to recover the credentials for an FMCv300? The individual who managed the FTDs/FMC left the organization and the folks that are supposed to now manage the environment cannot find the FMC credentials.
| User | Helpful Count |
|---|---|
| 93 | |
| 58 | |
| 57 | |
| 53 | |
| 41 |
