Activity in Technology and Support
%SISF-4-ENTRY_BLOCKED- IP Device-Tracking causing issues ?
Hello everybody, we are currently testing Softwareversion 17.06.3 and see log messages on the switch from "Switch Integrated Security Features (SISF)". I guess those messages are related to device-tracking or dhcp snooping. %SISF-4-ENTRY_BLOCKED: Ent...
EEM applet variables and regex
Hi,Im fiddeling with various EEM applets and feel a bit held back by the lack of documentation. Or maybe my google-searching skills have declined. First: Is there an official documentation of variables somewhere? So far I have pretty much brute-force...
Resolved! CW9800M – Support for 10G on 25G Ports (Bay 1) with Dual-Rate
Hi everyone, I hope you're doing well! I was wondering if anyone could help clarify a question about the Cisco Catalyst CW9800M Wireless Controller. Does anyone know if the 25G ports (Bay 1) on the CW9800M can operate at 10G when using dual-rate 10/2...
MST Root behaviours between two regions
Hi,I have two switches that are configured for region A, and now I need to connect them to some switches that are in region B. there is concern around spanning tree loops and I want to make sure my configuration is right.so my understanding is that a...
Resolved! Cisco cEdge ISR4331 Factory reset
Hello All¿ Anybody knows to how to factory reset trought CLI command a Cisco cEdget ISR 4331 with SD-WAN firmware? a vEdget is with request sfotware reset... but in cEdge routers this command is not supported. Cheers
cx agent on aws
Hi CX cloud team, I need to migrate this product to aws, is there any limitation to run cx agent on a bare metal on AWS with hyper-v?as cx agent only supports local vm configuration only(vmware and hyper v) Im think of using a bare metal to install h...
"Handling event from device" Then VPN goes down
Hello, We have a policy-based VPN to a third party that randomly goes down briefly, but after it comes back up, we still lose messages for 15-20 minutes. Each side says they have no touched the config since it was created years ago. We got on a call ...
Need Help with Network Configuration Task
Hello everyone, I hope you're doing well.I'm currently working on a network configuration task and I'm having a bit of trouble completing it. I still have a lot to learn, and I would really appreciate any guidance or help from this community to bette...
Cisco CUCM Integration with Imagicle UC Suite
Create two SIP Trunk Security Profiles to listen on different SIP port for Call Recording 5070 and Auto Attendant 5062. Create two SIP Profiles. Create two SIP Trunk. The first SIP Trunk will be used for Call Recording, use 5070 as the destinati...
ISR4431 reboot loop with %CPPHA-3-INITFAIL (0x43)
Hi all,One of the two ISR4431 started to boot into errors after power outage. I can enter ROMMON, able to boot many different IOSes (including external TFTP download via Gi0 interface), but all of them got stuck & reboot with the messages below (more...
Migrate vManage Controllers from MSP Cloud to Cisco Hosted?
I have a scenario where I want to migrate the SD-WAN Controllers from MSP Cloud ( in this case BT) to the Cisco Hosted Cloud or AWS Public Cloud hosted model. Ideally retaining the edge devices and licensing to be used with the new controller setup...
WLC 9800 IOS Wave 1 APs compaitility
Hi, I was doing research and know that 17.9.3 was the latest IOS that reintroduced compatibility for Wave 1 APs. What doesn't seem clear is whether that is the only one. Does reintroduced mean all of 17.9.x will be compatible? Or is 17.9.3 the latest...
OSPF route preference for 2 subnets
Good day All,I have 2 N9K-C93108TC-FX3P running ospf (rtrA and rtrB) right now the way ospf is working is that all the routes are currently going over rtrB. I have 2 subnets 10.4.1.0/2410.4.2.0/24I don't want these 2 to go over rtrB but instead need...
PCA Network and Service Visibility for Critical Infrastructures
Cisco Provider Connectivity Assurance enhances visibility and performance in critical infrastructure networks by leveraging intelligent data input for smarter decision-making. As data volumes surge due to digital transformation and AI adoption, orga...
Resolved! After upgrading Snort2 to Snort3 errors popping out and other problems
Hi All,Hope everyone is doing great. I have upgraded my FTD Snort V2 to Snort V3 last weekend and it was successful but i ran into some roadblocks.Here are the list of problems encountered below:1) Error pops out that AMP cannot connect to cloud2) tr...
| User | Helpful Count |
|---|---|
| 113 | |
| 84 | |
| 73 | |
| 62 | |
| 61 |
