Unlike CuCM and Unity connection Expressways are in any standard scenario uses separate certs per peer. Lets say if there are 4 nodes with 2 nodes set to expire on the same day and 2 other nodes cert set to expire on another day. When you export the...
Hi, Upgrading to Expressway 14.2 and I believe getting the CUCM Tomcat-ECDSA cert signed by our Internal CA is a pre-req. I've created the CSR and got it signed by our CA but when I go to upload our CA Root/Issuing certs to the Tomcat-ECDSA Trust Sto...
Hi, We have a system running, where we have the Publisher running on high CPU for the last couple of weeks. When looking into what is taking most of the CPU, then the rtmtreporter pops up. I have tried to look into if it will be okay to try and resta...
What is the use case of "Out of Dialog Refer CSS" on SIP Trunk?
HiI need to upgrade cuc 11.0.1.21900-11 to CUC_12.5.1.12900-56.sgn.isoI configured VM to link on the CUC_12.5.1.12900-56.sgn.isoBut when I initiate the upgrade, it doesnt view the filePlease Helpadmin:utils system upgrade initiateWarning: Do not clos...
Hi,I have setup new ITSP with this configuration : CUCM -- CUBE -- ITSP (via internet)Credentials provided by ITSP is correct because when I tried on phonerlite, it's registered and I can make incoming and outgoing call. But when I test it on CUBE, I...
Could anyone share the Informix db access default password. Cisco UCCX Version 11.6.1
Hii am trying to establish a trunk with an ITSP using cisco router. however call is not going through and giving below error code. Reason: Q.850;cause=38please see a sample sip capture form the router where it recived call from cucm and after matchin...
Like the title, CUCM 11.5 supports, does it support OS? thanks!!
Hello Everyone,I have 2 cubes no HA in two seperate date centers. I would like to test the failover from the Cube1 in data center1 to cube2 in data center2.I have 2 tenants configured in each cube. What is the easiest way to unregister both tenants i...
Hi,I am configuring a VG350 voice gateway connected to Asterisk over SIP, and was wondering if there is any way to do a ring group in the gateway itself. I am used to using hunt-group in routers, however this is not an option in the gateway and I can...
Dear all,we have configured, on a ISR4331/K9, Cisco IOS XE Software, Version 16.07.0 Cisco IOS Software [Fuji], ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Versi on 16.7.1, RELEASE SOFTWARE (fc6), the following set of commands: controller E1 0/1/...
The requirement for the Deployment MRA on Expressway E and C I've done it all (such as create zone between C & E, Resolve DNS A Record and SRV Record Expressway C & E, public certificate, NAT IP lan external Exp E to IP Public) and i using ACME for ...
According to the documentation I can find, the NIM-4FXSP is supported under CUCM 10.5.2. However, it doesn't appear as an option for cards when we look in the system in setting up a 4331 (there is a NIM-4FXS). What device pack is required to get th...
I have a Cisco 2811 router with a T1 card that serviced a PRI. It was configured as an MGCP gateway. Caller ID Name and Number worked fine. I replaced it with an ISR4331 but configured it as an h.323 gateway. After placing the 4331 in service, incomi...
.jpg "VIP Expert"){kind=icon}
