Resolved! WEBEX Softphone - outgoing calls
Hi. I am using webex app on my laptop and all outgoing call are disconnected after 120 seconds. I don´t know how to fix it.
Forum Posts
Microsoft is set to deprecate EWS with applications that integrate with O365. We use Cisco Unity for OAuth authentication which uses EWS. Microsoft has said that we should going forward use Microsoft Graph API however Cisco AS team is saying that Gra...
Resolved! CUBE does not send OPTIONS signal
Hi Everybody, Currently i am using the ISR4431 as a cube, add an additional pstn sip to telco, but failed to make outbound callOther SIP connection to pstn are fine, except this newly add sip connection.Connection path CUCM ---(sip)--- CUBE ---(sip)-...
Hi folks, hoping I can get some advice on troubleshooting steps for a calling issue I am having. TAC has been assisting for 3 months but has been no luck as yet, so running out of ideas.Environment CUCM 12.5 SU6, CCX 12.5, CUBE (router 4451 with 17.1...
Hi, We have a SIP trunk to Webex Calling on a Local gateway IOS-XE using a voice tenant. We are required to restart the SIP service periodically for a different reason It takes a full 2 minutes for the trunk to come back into a registered state. Is t...
Hello, I ran into an issue where CallManager service is discarding incoming SIP message due to too many headers, the problem is quite obvious in the trace due to: |AppInfo |SIPTcp - Ignoring message with too many headers from 10.0.0.1:[5060]. Only al...
Hi, haven't found any info about it: When you set a new call forward on Self Care Portal - the chosen number will be saved, even if it is not enabled, in case you wanna use it again, just click on it. Questions:1. Where is it stored? 2. For how long ...
From the CUCM call logs, we see that the Voice Gateway sends a BYE message which is causing hold calls to disconnect at the 5 minute mark, meanwhile a rare few get disconnected in 30 seconds at the mark while being on hold. What setting would cause ...
Resolved! How to change User Locale in CUCM
How to change User Locale in CUCMCan I set the default setting to Korean without changing User Locale in CUCM's phone settings?Most phones display in Korean without editing User Locale settings.However, some phones require the User Locale to be chan...
Are we need any integration license to connect Microsoft Teams with CUCM?Also, what licenses are required on the Microsoft Teams side?
We're trying to integrate our existing Avaya phone system to Cisco CUBE and Teams Direct Routing. We're able to make the Teams outbound calling (Teams to Avaya ext. or external PSTN/mobile) partially work -- we were able to make the callee's phone ri...
Has anybody used FileZilla Pro Enterprise Server as an SFTP server for CUCM? We've seen that the Solarwinds SFTP server has issues with CUCM, and would like to avoid getting another SFTP server that is incompatible. Thanks
Hello community Excuse me, could you help me with the difference between C8300-1N1S-6T vs C8300-1N1S-6T-V? I can't find information about C8300-1N1S-6T-V. I would like to know if I can configure HA between 2 C8300-1N1S-6T-V devices? Thanks for the he...
Hi I wanted to know if it is a requirement or merely best practice to install the latest DST cop files. We are running version 14 and i see there is a new DST cop files called ciscocm.dst-updater.2024a-el7-00.14.0.1.cop.sha512 Several years ago we h...
Running in to a weird issue. No impact, just annoying. This is in both CUC 12.5 SU5 and 14 SU3.At the top of LDAP Configuration (and pretty much everything else) is a Status section that by default states - Status: ReadyHowever after clicking Save,...
