I'm building a new HX cluster into my production environment which consists of a new management VLAN id. Currently my FI should be using disjointed layer 2 because I have fixed the port channel group to carry certain VLAN only. So with this, may I kn...
Hello, I am trying to figure out the issue with kvm console on APIC M1 server I am having following issues - 1. when i click on open kvm console in cimc, it gives me error message that i am using old java version (instead of 1.6.0_14). But I am run...
hey, me SNS-3595 ... my upgrade process stuck at 5% Download...reboot cimc not possible... upgrade in progress restart new task... upgrade in progress SFTP Server log : session timed out...Network Port : shut ... no shut... no effect is there a opti...
Hey, I’m currently try to add UCS X-Series Chassis to 6545 FI. This fails with „Chassis X has an invalid FRU“. I have updated FIs to the latest recommended Patch Level, also updated Capabiliy Catalog (4.2(3b)) but the error persists. Issue might be ...
I have installed a PCI card to the PCI Riser 2 with a Kingston M2 SSD. There is no way to get it to boot from that SSD. Please help
Hello everyone, I have two C220 M5's with 1387 VIC cards. I can not for the life of me get these servers to connect to the switch at 40Gb and don't know if I'm missing anything. I can get them to connect to the switch with a QSA and 10Gb adapter. I a...
The "Get-UcsMemoryUnit" command provides lots of information, but not the PID. I read somewhere that "Get-UcsCapability" is supposed to provide the PID for the associated ManagedObject but it does not appear to accept Cisco.Ucsm.MemoryUnit even thoug...
Hello,`SysRq` can't be defined in a user defined macro...Help...
Long story short, one of my customers wants to move from a pair of FI6200 with one chassis of blades to a new single FI6400…Not IMM. Each blade is running VMware ESXi with Boot from SAN. I am not aware of any way to migrate the profiles and existing ...
Hello,I can't update my Redhat 8.1 to 8.4 because the megasr module is not available for Redhat 8.4 !https://software.cisco.com/download/home/286318809/type/283853158/release/4.2(1c)Last month update gives only drivers for Redhat 8.2, is it a joke?An...
I am taking over an existing HyperFlex cluster. I am attempting to upgrade the HyperFlex Storage Connect system from 2.6(1d) to 4.5. However, I'm unable to upgrade to even the 2.6(1e) version because (I assume) the Storage Connect system is currently...
Hello,I acquired a BE6000M M5SX for a customer a year and a half ago. It has been stored in good condition. We have just started it. Unfortunately it refuses to start..... The initial procedure in standby goes well (all the LEDs on the front are gree...
Hi everyone, I have a customer that is planning to migrate from Fabric Interconnect 6332 to 6454. And upgrading the existing IOM on 5108 Chassis from 2304 to 2408. From the Cisco official migration guide, it stated that 6454 is not intended to replac...
Hello, I will be doing a new HX install (FI's included), and I was wondering if I should be considering IMM. Since IMM is SAAS based, I was wondering how you would manage the environment if the Internet is down. Any info that will allow me to make t...
Hi,I've tried scrubbing servers a few times yet I never seem to find a proper repeatable way to scrub a server. Steps I've tried:First we activate the Scrub Policy that is set to Scrub Everything on the Service Profile.Then we try one or more of thes...
.jpg "VIP Mentor"){kind=icon}
