Good day guys, At our company we have a WLC 2504 wireless LAN controller, controlling a number of WLAN's. Recently we changed the password for one of the WLAN's and had no issue reconnecting any device to the network with the new password, however ...
Can anyone explain me about the Polling parameters in Monitoring policy of the Cisco Prime Infrastructure ? Is it like built in Cisco Prime or we will need to install it ?
I have a HA WLC 5520 and we have ordered some new AP's (AIR-AP2802I-E-K9). They connect and register to the WLC however, they do not pass any traffic through the WLANs. Looking at the cisco help forums I can see that CSCvc67005 is the problem. Thi...
Dears,have the APs to be directly connected to the c3850 switch??not to another switch??and if the c3850 none poe so what is the solution now?Thanks in advance
Hello, I am looking to build a Outdoor wireless mesh with approx 250-5000 AP's on completion. This mesh will also have the requirement for supporting ethernet bridging. I have read every guide and can find nothing related to how the mesh APs show b...
Hi Guys , We have 2 Cisco 5520 controllers in HA for our infrastructure , i am facing a serious issue regarding secondary Controller as its not booting after a power issue . Its giving the attached messages on the console . I will appreciate if you...
Hello All, I'm looking to setting up secure Guest Wifi to the Enterprise environment, any suggestions? Thanks,
Hello experts- I want to configure my wlan cisco 2504 as a router like I want to use port 0 for LAN interface and port 1 for WAN. On port 1, I want to use public IP and need to enable one to many NAT on it. so that any traffic comes from port 0 i.e l...
hi every body .i want get ccie wireless certificate andI worked 6 months as an amateur in this field but I do not know whatPrerequisite There are for CCIE WIRELESS Book list & Where do I start..plz help me know
Good Morning! I have a 4x 2802i APs that need to associate to a 5520 Controller. They are on the same subnet/vlan with the same gateway. The tricky part is that we cannot connect the SFP+ cables yet, as they are being ordered. How would I go ab...
Hello, I dont know much about wireless technology, so I hope someone can help/guide me in the right direction here. My company wants to have alerts/alarms when the client count reach a limit in APs, is there any way to configure this in WLC or in...
Hi, I have the following issue with the wireless clients in my setup. The same client when connected to an access point on 802.11bn gives very low speed and while connecting to another access point on 802.11ac given good speeds. The access point m...
Hello All, I got issue when I removed APs and redeployment to another site! when I removed them I cleared everything inside the AP and put new IP add and New IP add for new controller. but when install these APs onsite it will keep join to old WLC a...
All I have a new issue. My access point was working fine then all the sudden all my devices that are connected wirelessly just dropped off the network. I logged into my access point and did not see an Access Point listed under the controller. It is c...
I am tring to configure CMX 10 for asset location tracking. We don't have Cisco Prime. how can i achive it Virtual CMX Version : 10.3.1-35 5520 Wireless Lan Controller Version : 8.5.120.0 Prime: Not Exist The CMX is not accepting the MAP in JPEG...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 10-15-2026 05:58 PM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM | ||
| 08-10-2026 11:32 AM | ||
| 08-06-2026 09:29 PM |
| User | Count |
|---|---|
| 5 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |
