Wireless

Hi,Have Cisco WLC 2504 in HA, I tried to connect the Access point CISCO AP AIR-LAP1131AG-E-K9. Access point have taken IP address from DHCP server and able to ping from WLC.In WLC it's not joined well. Is this AP model support or not by WLC?In WLC fo...

Hi,I'm building a lab with WLC4404 and freeradius + daloradius gui.WLC can comunicate with the freeradius but my problem is that the users can login and no  matter in which SSID they connect they get in. I want to know the way to policy this on the f...

We install two controllers WLC 5508 with terminals 1600 and 1242, since the commissioning we have the AP radio cuts every 4 hours as an error message:Log of the controller:08 Thu May 28, 2015 2:36:23 p.m. AP's interface: 1 (802.11a) Operation State U...

Good day to you all, At this moment we are running with Cisco 3502I AP’s, N standard.I know that the “rule” is for optimal efficiency 25 clients per access point.We are going to change our wireless system to 3700i Access point.And we are going to use...

Hi  We created a new RSA cert but the users that are using the new certs cannot join to WLAN, but when they choose the old cert they are able to join to WLAN. We have a 5508 and we are using WPA2/AES 802.1X, we have on the LAN the Server RSA CA What ...

We just purchased 2 controllers 5508 and many CAP3702.  I'm searching the option where the AP can communicate directly each other instead using controller port but still be managed by the controller for coolest feature like clean-air....I follow the ...

I have 2 APs in a mesh configuration WITHOUT an WLC.  If a wireless client connects with the root AP all vlan traffic is passed.  If a wireless client connect to a non-root AP on the native vlan 244 traffic is passed but no other vlan traffic is pass...

I'm configuring SNMP on my Flexconnect Access Points. I configure the SMNP settings on the AP cli, and all is working 100%. As soon as I reboot the AP, the SNMP Config is gone (the rest of the config is still there) It seems it is being override by t...

Hi to everyone,I have problems to join an AP on the controller.  AP model is: AIR-AP1242G-E-K9 (They all are the same model, already 15APs on the controller)AP is reseted to factory default. DEBUG OUTPUT on AP*May 27 14:35:14.631: %LINK-3-UPDOWN: Int...

We have currently a setup with two 5508 WLAN Controllers (firmware 7.4.110.0) configured for AP SSO. Due to some network changes the IP address on the management interface and the redundancy-management interface must be changed to a new IP-range. As ...

Hello,I have problem authenticating Microsoft Surface 3 PC with WPA2 enterprise WLAN.All other PCs work fine. Any idea? ThanksJohnny 

Hello, need help for my AP 1142....all users using mobile always disconnecting please see logs 1Mar 1 02:57:50.139InformationInterface Dot11Radio0, Station 28cc.01c5.66ff Associated KEY_MGMT[NONE]2Mar 1 02:57:48.813InformationInterface Dot11Radio0, D...

Hello;I know there are many inputs into the DFS algorithm but I have 6 out of 11 APs operating on the same 2 * 20Mhz channels (36,40) , 4 are on (44,48) and a final on (64,60) - I have extended UNII-2 Channels enabled and have excluded 108 & 112, so ...

well I want to design a WLAN with 802.1x and EAP-TLS . We have a WLC 2500 , and bunch of Cisco AIR ,and Cisco ACS 5.4 as radius server.So we need a CA root. does WLC support built in CA ? what about ACS ?is it recommended to to configure WLC as CA se...