Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
I have a pair of WLC 5508 in HA pair running version 7.4.121.0, last week I have two sudden reload on my active WLC. Here's the error from my syslog server on the first sudden reload. The second reload has almost the same logs.10.x.x.234 - active10.x...
Resolved! Wireless controller for Branches
I have a central office (with 6 or 7 AP) and some Branche office (with 1 or 2 AP each).The connection is based on poorly performing lines (mostly VPN).I want to optimize and centralize the entire wireless network, converting the existing stand-alone ...
Hi guys,Would you use AIR-ANT2566P4W-R antenna with AP 1240? This AP supports 802.11a/g and has 4 external antenna ports (2ports for 2.4GHz and 2 for 5GHz band).Ant2566 is for dual-band AP...For me it looks like not the best practice, but to buy two ...
Which lightweight access points (LAPs) do the 2504 Series WLCs support ?
Plain and simple what are the best ways to handle PCI compliance over a wireless network. The first person that says create a seperate SSID will not get rated ... Mainly in regards to: Segment the wireless network from other network traffic (Section...
I have Cisco WLC 5760 that needs to be integerated with CISCO ACS so that users on WLAN can be autenticated via the ACS.i am looking for a details step by step plan to integerate the WLC with ACS and then how to configure the ACS to autenticate the u...
Hello everyone,I am attempting to deploy a wireless solution, and can ping my ap from the controller, but can not see the ap in the controller. I believe there is a firmware issue. Can I have a second pair of eyes on this as of now the ap does get an...
Dear, i have 12 caps(3602) and one 5508 controller, i have configure all the things, but when i have enable the hight-thoughput (n mode), then no win7 laptops are connecting, but when i will disable it then it is connected with 54 mbps, so what will ...
Hi,Can a Cisco Autonomous Bridge connect to an LWAPP AP and re-broadcast the SSID's? As in acting like a wireless repeater?Thanks
Hi All,We have an existing 4400 controller with MAC filtering for clients configured. Right Now, we are migrating to 5500 WLC and ISE setup.We want to use MAC filtering due to company policies on the new Controller as well as ISE. Is there a way (fro...
Resolved! WLC Captive portal certificate
Hi NetProI have a WLC 5500 with software 7.3, and some SSID it's using web authentication with a internal custom captive portal, and the configuration works without problem, but, when a client connect at captive portal, the portal captive show the er...
Hi FolksI saw the below in wlc controller ,what this mean,how to fix this issue if anyMost Recent Traps SNMP Authentication Failure: IP Address: 192.168.10.2
We are running 7.6 on our 5508-WLC. We have a number of issues w/ 'i-clients' when they go asleep. From what I can tell, I need to enable the 'sleeping clients' feature (not just the session and idle timeouts). On our WLANs we use Layer-2 (WPA+WPA2...
I have a WLC 5760 and i did below configuration for WLAN:wlan 3 85 GUESTS client vlan 85 no security wpa no security wpa akm dot1x no security wpa wpa2 no security wpa wpa2 ciphers aes session-timeout 1800 no shutdownthe ap is joined with WLC:EFFAT-W...
I have started to look into configuring our 3850 as a WLC I enabled the command wireless mobility controller Then I tried to connect to <switch ip>/wireless I just get a dead page. I configured the wireless management vlan but still no joyWhat basic ...
