Hi,I am stuck with an AP2802I that does not boot with its LED remaining off and nothing appearing on console.I already tried several different console cable with USB to Serial adaptor and and with a desktop (so without adaptor).I already tried to cha...
Forum Posts
Hi,I'm looking into ways to restrict traffic to my management GUI of the 9800-40 WLC.In the 5520 we have CPU ACL's deployed, restricting access.I know that I can attach an ACL to my management interface but what about the mobility traffic between con...
Hi,when I look in the mac address table, I don't see the VLAN for a particular WLAN under the trunk port of the switch which is connected to FlexConnect AP. If AP performs tagging, why I don't see it in the mac address table?
Hello Cisco WLAN-experts,we are running a Cisco Prime 3.8 with actual patches and have a nasty problem with Prime maps.Apparently, since we are using 3800-APs and use FRA to deactivate 2.4GHzAntennas and use 5GHz-antennas instead.But I'm not sure.So ...
hello, I am using WLC9800-40. I want to use DHCP on the WLC and not on the DHCP server or switch. Please tell me what settings I need to do. andWhether reserved only should be checked. Please tell me what value to put in the ipv4 helper address. than...
Resolved! No client mode in AP C9130
I am using AP C9130AXI-B with C9800, I need to configure the AP as client modeBut I can not able to find that in the liste "AP Mode" inside c9800 web.Any idea ?
The customer's equipment is relatively old, and it is found that the SSID of the wifi6 signal cannot be searched. Can only the radio frequency of wifi5 be reserved, for a certain SSID on the 9800?
Hi, We https://trackerwave.com/ RTLS company, provide indoor navigation, asset tracking and other solutions using BLE tags. Our RTLS platform is integrated with Meraki and other APs to get BLE ibeacon data.Now one of our customer using cisco cataly...
Error message received. It tries joining but don't get IP address. then send this error *Nov 28 12:57:51.535: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_record.c:169 Pkt too old last_seq_num : 1,Received sequence num: 1 distance: ...
Resolved! Cisco Aironet 2600 TLS 1.2 supported?
Hi,Is it possible to set up TLS 1.1, 1.2, or 1.3 with the Cisco Cisco Aironet 2600 serie?If so, do you know how to do it?The last firmware release 15.3.3-JF15 ; does not mention TLS versions compatibilityhttps://www.cisco.com/c/en/us/support/wireless...
Hi is there a Way to get a list from Rogue AP´s where sending with 160 MHz Channels ? I could extract it from the CLI on a C9800 but i am looking for a much elegant solution. Maybe someone knows how to get this information from Prime or DNAC. Conten...
We experienced Issues regarding network-connectivity, I looked into some loggs on our WLC 9800 and saw a bunch of loggs like this:.Oct 11 15:51:27.768: %IOSXE-4-PLATFORM: Chassis 2 R0/0: cpp_cp: QFP:0.0 Thread:224 TS:00001035332249163839 %SWPORT-4-MA...
I am looking for the factory reset procedures for a Cisco Aironet AIR-LAP1142N-A-K9? I tried the usual procedures without success. I do not have the login credentials or secret password.
I have a problem with backup configruation from WLC 9800-L via TFTP. I get this message "Error in Configuring Backup & Restore Error opening file connection timed out " when I set backup. I have set up automatic backup (archive) on switches in this n...
Resolved! need to combine 1832 ap to join 9115 ewc
we have 1832 wireless environment, and now need to additional aps, due to eol we can not by 1832 aps. therefore we are panning to buy catalyst 9115 ewc and use on same environment with 9115 ewc.
