Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi, I have a mobility express controller in the 8.10 firmware version. I am trying to upload the certificate using the cli after following the defined proccess for getting the encoded pem file. I have been able to do it in a 8.0 version wireless cont...
Hello Team, Kindly advise me which cable can use to power the IW3702-2E-E-K9 AP using a POE switch? I was wondering if the normal RJ45 will do? Also, as a second option which power injector will work, the customer is based in South Africa. Thanks.
Dear IT, We have Cisco WLC Model No: AIR-CT5508-K9 with Software Version: 7.6.110.0Suddenly, it started to hung and stopped working randomly. I can say it stopped 2-3 a week. After we powered it off and started it up, it worked fine.I have a copy of ...
I have implemented a Meraki wireless LAN at our location.SSID is set to PSK and WPA2I'm in NAT mode with no splash page.Everything is in DHCP.Everything connects seamlessly except for the Sharp MX-C304W and the two HP LaserJet Pro MFPs.auth_mode='wpa...
Hi, we have a pair of WLC 3504 and we need to reboot them in order to install a new certificate just uploaded. Is there any chance for reboot one device per time in order to don't interrupt the wireless service? We see the cli command: reset system ...
Resolved! Wireless Compatibility Matrix
Good Day, Checking this matrix:(For AP's compatible with WLC Firmware Version: 8.5.160.0) https://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html The matrix lists AP models 1600, 2600, 2800 ect.I am 99% sure abov...
Anyone come across a situation where some clients on the network are connected to wifi then suddenly they have a 169. IP?I have checked and there are still available IP`s in the pool. It seems to be happening randomly.
Hi,Using cisco 8821 Wireless IP Phone, AP is just outside of the room where the Phone is, but the signals are very weeks, can some1 suggest me how to improve the signal strength. kaleem
Hello Everyone,I have AIR-AP1562E-B-K9 Mesh outdoor AP. It was working before. Today i have found in WLC, under AP join, it is not showing real ethernet mac address but instead showing 00:00:00:00:00:00.But the ap has received the ip from DHCP. I can...
Hello, I got a site (flexconnect, RF group separated) disconnected from the WLC. Just after reassociation, I saw radio reset in all APs from that site. The question is: what would have caused that radio reset? does an AP association trigger RRM? th...
Hello,we are trying to configure guest WLAN in foreign and anchor topology using two C9800 WLCs.we are receiving the error messages below== ANCHORJul 14 18:38:06.288: %CLIENT_EXCLUSION_SERVER-5-ADD_TO_BLACKLIST_REASON_DYNAMIC: Chassis 1 R0/0: wncmgrd...
I've just configured C9800-L-C-K9,joined access points C9120 all show operation status "down" , admin status "enabled",what could be the reason of this problem ?
6 Story building, it's a rectangular design, 30 units on each floor, 15 units per side, floors 2-5, the bottom floor is comprised of all offices. 150 apartment units total, all full of people. See my attachment below of the screenshot I took using M...
Resolved! 9120 AX AP
I have a problem connecting mobile phones in some of our clients in the newly deployed 9120 AX AP, they were connected before in 3600 using their credentials (AD Account). They are not having problem using their laptops with their credentials connect...
Does anyone know of a way , I can't find how to set the power transmit on the dashboard, just add the radio transmit section for the mr-12 type access point as below with the status always "off", how to fix it?
