Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello for everybody. What is best way to register a certain number of these access points located on a remote site on a controller located in the main DC. To paraphrase a little, there is a site where there is no wifi. Completely new access points of...
Hi, I have AIR-AP3802E-D-K9 i am using "Lightweight Access Point" image and connected with my Wireless controller 2500 series). When i enter command (within AP) "Sh Flash" or " sh version" in telnet or ssh it not showing IOS version in the form of ...
Hello,Perhaps this is just the best I can expect from this particular AP, but I was hoping to break 300 Mbps with this AP setup, as I believe according to the charts, I am getting MC9 speeds and should be able to hit this. Setup / Info:vWLC VM runnin...
Hello, We have a WLC 5520 with APs in flexconnect mode (local switching). I'm almost sure it's possible, but could you confirm we can mix 3802E/I AP models with 3702I/E AP models in the same APs group ? Many thanks by advance.
Resolved! Flexconnect AP stuck in Standalone Mode
Hi all , I have all of my APs configured under flexconnect at the remote site .I have one controller at the main office .There are two redundant MPLS links going from the main office to the remote site . Now the issue is , whenever my MPLS does a fa...
Hello Team, can any one know about this certificate if this get expired. Cisco Manufacturing CA SHA1 Cert
Hi guys,currently we are using a central wlc 5508 and AIR-LAP1142 access points with flex connect.We got a new branch office where we have bought 9120AX access points for. Futhermore, we bought a C9800 WLC.My idea is to setup the new wlc in parallel ...
Hi ISE 2.2 patch 16.Been having issues with Guest portal, because of lock down, the guest portal isn't being used so looking at the issue. 4 * PSN configured for CWA, when I click on the WLAN, the redirect comes up, not secure even though a new certi...
I'm afraid I need some hand holding as I am a bit overwhelmed at the moment.I have four AIR-CAP3502I-E-K9 with LAP without a controller. I would like to(1)Update the LAP to the latest version without using a controller(2)Install vWLC as controllerI a...
Resolved! UNII-3 Europe / Germany
Hello Community,I would like to clarify the usage of UNII-3 bandwidth in Europe.According to documents and also from my experience in Europe it is not allowed to use UNII-3 bandwidth,but looking at cisco doc for example https://www.cisco.com/c/en/us/...
Hello Support, I have trouble where Cisco Access Points AIR-CAP2702I-E-K9 Not Connecting To Controller Below is the Error *Jan 8 03:59:35.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: x.x.x.x peer_port: 5246*Jan 8 03:59:35.347: %D...
How much distance should be there between 2 access point when we install at the site.Suppose we have 2 3802i ap at the site. Plz let me know the distance in length, I heard somewhere that it should be 10meter between 2 access point, is this correct?
Hello Team, Thanks for replying on my questions. Team i have little bit confusion regarding Channel of 2.4ghz band and 5ghz band. as i know there are 11 channel in 2.4ghz band and 24 channel in 5ghz band, i wanted to know who they select in our pro...
HI Team When users are connecting to the corp-SSID they are getting the ip from the WLC management sub net . In the flex connect i have set the Vlan and tested too but still no luck . WLC issue, Other Wireless-Mobility Subjects Below is AP detail...
Hello all,I am using an AIR-AP2802E-E-K9 (v04, created on 01/2018) with the new firmware ME-8-10-121-0. The AP works perfectly if it starts up after being stuck for the first time Board Init:BootROM-1.78Boot from SPI Flash, Safe ModeBootROM: Verifica...
