Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hello,I have two Cisco 3802i-E Access Points were I need a higher power level on the 2.4 GHz WiFi that I will get a stronger singal, because I want to build a Mesh between them because I am not able to setup a cable on the other site.According to the...
Hi there "standalone access point mode" -> Which means that there is NOT special / proprietary Hardware (Rack device) or Software from Cisco necessary... so i can use it just as an "normal" access point (as a bride) in EVERY (Cisco-independent) netwo...
Can anybody help? Since Android 11 was released I can no longer connect some users to a SSID using Meraki Authentication. The firmware update from Android essentially removes the users capability of choosing to trust a certificate. This is apparently...
Hi. Printer Issues Wifi, Wireless Network Management We have two RICOH printers here at work and all computers connected to the Ethernet on our network can print just fine (we have CISCO Switches). When people use the wifi, however, they can't see ...
Hello,vWLC is setting at ESXi and it has a management interface 10.0.10.2/24-vlan10 and a dynamic interface 10.0.20.2/24-vlan20. The ESXi host trunk to a physical switch that has vlan10 with ip address 10.0.10.10/24 and vlan 20 with ip address 10.0.2...
Resolved! Wireless Bridge between 2 buildings
Hello everybody,we need to connect 2 buildings - 2 networks with a wifi bridge at gigabit speed.The network uses vlan trunks, distance about 30 meters.Can you suggest units?Thank you,
Resolved! 9800WLCs copy config from lab
Hello there We are trying to migrate WLCs 9800s ACS TACACS+ to Cisco ISE. We were successful in migrating in the lab, but we have issues while on the actual production, is there a method to copy the lab configurations to the actual production. in s...
Resolved! Wlan error
Hi all trying to access wlans but getting the attached error all flex-connect is turned off but still can't access it
1852 restart repeatedly,After upgrading the firmware under u-boot, I can enter the prompt and show version, but restart immediately。What should I do?Can I use part2 to boot? ——————————————————————————————————————————————(RNAQ-C7) # bootipq tftpSpeci...
I would like to use IPSK and I undestrood it works like this:-I will configure one only common SSID-user who will connect to IPSK_SSID and use PSK_123 will be connected to VLAN 123-user who will connect to IPSK_SSID and use PSK_456 will be conn...
Hello Everyone, Scenario - External WebAuth server is using port 8443. In webauth parameter map -redirect url used set as https://External_WebAuth:8443/login.html Two WebAuth ACLs (WA-Sec and WA-Int) are created automatically using redirect port 443 ...
Good morning guys I have two WLANs ("POTIGAS - Coletores" and "POTIGAS - Teste interno") that are configured in a 2504 WLC and that are delivering a wrong default gateway to the wireless clients. The dynamic interfaces are respectively on VLANs 40 an...
Hello, Any one using External Webauth with append parameters? In the AIROS if external webauth (Web Authentication on WLAN Controller - Cisco) is used for SSID, the request to external URL is redirected by appending parameters - AP MAC address, Clie...
Hi I have a MR72 and when I plug it into the wired network everything is great. Now i need to to be wireless so when I plug it into a POE injector (no wired network connectivity just using the POE injector for power, just wanting to use wireless) It ...
I have a Health Care Customer about to Implement C9800s in local mode in HA - 9130s:Has there been any feedback or Caveats reported/known with client devices roaming from 9130.ax to 2800.ac/2700.wave1 environment? A little salt and pepper? IMO..I don...
