Hi, I have a couple of N3K-C3132Q-40GE with nxos.9.3.2.bin. I want to configure that devices as leaf but when I try to enable feature fabric forwarding is missing. Does N3K-C3132Q-40GE act as a leaf? Why is this feature missing? Thanks in advance
Hello, EveryoneI have a few questions about Etherchannel. When configuring Etherchannel with 2 ports in Cisco equipment, bandwidth is displayed as double in show interface port-channel, but in reality, 5:5 load balancing is impossible by Etherchanne...
We have a scenario with 3 switches Nexus 7K, topology attached run OTV between them, topology Multi-Homing. Everything is working.
We need to UPGRADE IOS in the Nexus 7006 that is located in the site-vlan from 7.2 to 8.3 version IOS. After UPGRADE ...
Hi folks, Running into an issue with one of the N9K-C93180YC-EX switches, where I cannot access to the switch via its console port. The two switches were purchased in the same contract, and are recently racked and stacked to prepare for new services....
Hi i have two of four new 9504 chassis being RMA'd by Cisco following all the line cards in the chassis powering down and refusing to restart at roughly the same time. I have two DC's with two 9504 in each DC. One chassis in each DC had the issue. Ca...
Hi team, Please I want to be sure that the command "mac-learn disable" in SW NX 9K disable the reading of the MAC address without any impact for our VLAN or infra. Thanks in advance.
I have 4 new 9504 switch being prepared to replace catalyst 6509's. They have been sitting in the DC's for several months powered up config in place waiting for the migration. A check to day show 2 of the 4 switches reporting the following; Mod Ports...
I have a 7706 running 7.3 with SUP2E and F348XP-23 cards. I am seeing different information on whether or not multiple destinations per monitor session are allowed. I did find this: Prior to Cisco NX-OS Release 7.2(0)D1(1), multiple SPAN destinat...
Is there anything special I have to do on VMware to get two 9000v's setup as a vPC pair? When I build the vPC, the link will come up and then throw the log up below and block all VLAN's from traversing the peer-link. If I put the same config on two...
Hi all.I'm a little bit confused about vPC object tracking during peer-link down and looking for some advice. I'm referring to this article about object tracking https://networkrare.com/cisco-nexus-enhance-object-tracking-boolean-or-in-vpc/ As per Ci...
Hi,N7K has 10 BGP neighbors.How to advertise only summary route to 2 bgp neighbors only. all routes should be advertised to rest of the 8 bgp neighbors. aggregate-address xxxx xxx summary-only advertises summary route to all neighbors. how to adverti...
Hello,I want to understand, from a design perspective, how a nexus 7k switch can be connected to catalyst switches in the distribution layer N7K will be used as core and DC switch at the same time (by using VDC I guess)What are the possible designs u...
We have dozens of 7700s in our data centers and I have configured my 7700's NTP exactly like the many which appear to be working properly BUT whenever I type 'show clock' on this 7700 I see the following: Warning: No NTP peer/server configured. Time ...
We had to open a TAC case to figure this out. Connected 1/3/9 and 2/3/9 on two sup6t in a vss pair to two separate N9K-93180YC-EX e1/51. Expected them to work and they did not. Replaced with an AOC7M cable and the links came up.TAC recommended to set...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
