I have a scenario where I would like to verify if a design will work. I have DC1 where I have an Nexus 5K's for LAN and an ASR for WAN using MPLS. In DC2 I have 9K's in the LAN and an ASR for WAN using MPLS. In DC3 I have 9K's connected back using...
Forum Posts
Resolved! Upgrade Nexus 7k
Hi there experts,we have to upgrade from 6.2(14) to NX 8.2(3)and it's big leap between the versionthere is a option to do it via ISSU or it has to be via cold bootbecause this are dual sup devices so we want the less impact for the production environ...
Nexus 5600, 7.3(8)N1(1): Configuring SPAN:Do you know how to remove the fabricpath encapsulation tag on Nexus 5600 switches?On Nexus 7000 switches this seems to be possible:int eth 1/41 switchport monitor exclude headerCisco Nexus 7000 Series NX-OS S...
Looking to see if someone can provide some info on this. I know that this inconsistency means that I have an SVI configured on one switch but not the other. My question is, what problems will this cause?The SVI in question is kind of a one off thing,...
Hello,I was wondering where the system policies are managed, such as __pfm_fanabsent_any_singlefanon platfrom Nexus7700 C7710: It's not visible under system-policies: 1# sh event manager system-policyName : __ethpm_debug_1Description : Action: noneOv...
how many FM does 9504, 9508, 9516 support? which slot # are these FM installed it?
Hi, I am upgrading some N7706s and they are not in VPC but have multiple VDCs on them. they have 2 x supervisor modules i.e. N77-SUP2E and they are current on version 7.3(0)DX(1) the plan is to upgrade them to 8.0(1. However, I am struggling to ident...
Hi I have bgp ipv4 unicast neighborship with 2 WAN routers. I learn few bgp prefixes that i set community for. I have a bgp ipv4 multicast peering with a firewall. I want to advertise prefixes learnt from the wan-router via address family ipv4 unica...
I have a lab scenario as follows:2 x Nexus 9300 (one of them is a border gateway)1 x external router running OSPF Summary of issue: Want to only advertise the network prefixes to external OSPF peer and not the /32s evpn routes. The border gateway i...
VTP VLAN configuration not allowed when device is in Client/Secondary server mode - VTP not enabled
Had a VLAN that existed before but went missing. When trying to create the missing VLAN again (on a Nexus 9000 series switch) we get the message "VTP VLAN configuration not allowed when device is in Client/Secondary server mode" We do not have VTP e...
Hi, I am upgrading some N7706s and they are not in VPC but have multiple VDCs on them. they have 2 x supervisor modules i.e. N77-SUP2E and they are current on version 7.3(0)DX(1) the plan is to upgrade them to 8.0(1. However, I am struggling to ident...
Resolved! Nexus 3548-XL switch-mode
Hello, I would like to confirm which switch mode is running on my Nexus 3548-XL. (N3K mode or N9K mode)The result of the output is as follows, would you please tell me how to check it, thanks !!! N3548XL# show system switch-mode Switch mode configur...
I can add object group and add into ACL on 6500 model. but I couldn't add "object-group ip address" on 7600 model. @ 6500 model.object-group ip address DENY01[IP address] [Netmask]exitip access-list extended OUT10000 deny ip addrgroup DENY01 any10000...
Hi, I'm using the IP Fabric for Media version 11.4(1) of DCNM to manage a N9K fabric. I have a couple of N5K switches that I use for servers that require access to the fabric and are connected to the N9K spines. DCNM shows the N5Ks as switches but it...
I am in middle of deploying Spine-Leaf design using Cisco 9396PX switches for my leaf and when i am trying to configure arp-suppression for VNI i found this error. Default vacl tcam size is 512 so i am freeing up all of that for arp-ether hardware ac...
