Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi all...Is there a way to setup call forwarding to a users external number (cell phone) without programming an IP phone?Here's the story, the regional managers in our office all work remotely and have office of desk here in the corp office, I've bee...
Running Communications Manager 8.5(1) with mostly 3945 router running 15.1(4)M6 at remote sites. Having an issue with dropped calls. The Caller Termination Cause is showing as "Temporary Failure". All sites are dropping calls from time to time wi...
HiMy Cisco 7960 IP phones are registered with SCCP right now. I uploaded sip firmware files in router Flash using tftp server. cisco 2911 ISR router is used as tftp server. After uploading sip firmware I reset ip phones but Phones are still registeri...
Is anyone out there using a ClearOne VH20 for integration a board room conferencing solution? I would like to be able to control a conference call via the ClearOne device using a Crestron control unit.Basically, I would like to be able to have more t...
CUCM 10.5, 2911 router with E&M card I understand the basics of making this work with multcast. Blocking the source from the CUCM so the phones listen to the router instead. Does this work on MGCP? Will my E&M card work not being programmed into th...
Dear friends, I would like to know which is the exact version supported for Apple MAC book , We have cucm 9.1.2 and presence 9.1Please help me to guide or linik from were I can download the software on the macbook it self.if possible configuration he...
Hi all, I was able to block offnet to offnet call transfers in my CUCM 7. environment thanks to the "Block OffNet to OffNet Transfer Service Parameter". But I have discovered one scénario that allows call fraud though:We have to internal callers A an...
Hi Everbody :)We have some Ip phones (model 7942) that is showing English instead of the language I set on the end user in our CM (Unified Communication Manager). I can't see why the phone takes on this default language and when the user is logging i...
friends i have cucm 6.1.3 and becz of my MSN/DId which i am getting are having different digits i am forced to move from 4 digits to 5 digits extension...right now my extension are 3000 series and my head number 554 - 3XXX series ... but now when i a...
Hi,We moved a DID trunk from a PBX to a FXS/DID card. Supposedly the telco is using wink-start. As soon as we enable the port and plug the cable in, the port goes seized on the inbound status of the port. I've tried each signaling type just in case a...
We have user A with ip phone number - 1000 and associated (remote destinaton) mobile number 9999 and User B - 2000When user A make a call from his mobile phone 9999 to User B ip phone 2000 , only calling number is getting displayed i,e 1000 not the c...
Hi guysIs possible to configure or remove the popup on ip phone assistant? On CUCM 5.x the assisant tell me that the popup on ip phone aren't showed. Now on 7.1.5 the popup is show! Is possible to configure to no show?RegardsPeterson
I've got a bunch of 7942's that aren't not showing any information for missed,received or placed calls. I've seen a few posts that point to incorrect vlans, or inaccurate opt.150's, however that's not my issue. We're running firmware SCCP42.9-3-1SR2...
Hello all,I have confusion on Jabber client (windows ver) licensing.I can see that in our Enterprise License Manager 9, Jabber UCSF clients are utilizing licenses. As per my understanding UCSF client is to use computer for calls only (as attached). I...
Hello EvereyoneUsing:Cisco Unity Connection version: 9.1.2.10000-10Office 365 - Outlook Online using Exchange 2013We have some Unity subscribers that are not getting their VM delivered to their email, these are just a few subscribers, around 3 or 4 o...
