Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello,I am planning an upgrade to 9.1 from 8.5. I want to use the UCT tool to determine current licensing as is translated to the upgrade to 9.1. I am unable to find it on the Cisco site. All searches in the forum's and online show I should find i...
We are running CM version 8.5 and have CER and UC integrated on our network. One of our support personnel wants to change the passwords on the systems (why exactly I do not know) but myself and another technician are worried about ...
Hello all,I have set up a voice lab with below topologySCCP Extension (2001/ Mask: +14082022001)----CUCM 7.0---H323-----CUBE-----SIP------CUCME---SCCP Extension (6001/Mask: +861062286001)However, when 2001 call 6001, 6001 only rings for 1 time, and 2...
here is my situation.Let say I own 777-777-1111. if someone called 777-777-1111, it'll route to my cucm and I need it to reroute to an external number that I don't own, let say it's 666-666-1111. And if that fails, it'll go to an external number 6...
We are trying to transfer a calls to an after-hours call center. Unfortunately we are getting a fast busy when we attempt to forward. When I run 'debug isdn q931' I can see the reason we are getting a fast busy is the number prefix is incorrect. I...
Is there any more to it than this?Here is the only way to use MeetMe with a 7936; 1. press the pick up handset to get dial tone 2. Press Menu button > Call functions > Meet Me
Good day all,I need to assign an employee a DID number. The problem is that he is in another state and I've only been able to ascertain that our translation pattern is setup for our state and area code. So how would I go about setting up a translatio...
Hi everyone,I am having a problem with remote 7945 phones that have been deployed. The remote connection is set for VPN connection to an ASA 5525. Many phones have worked but I have found that approximately a 1/3 of the phones are failing to launch...
Hello, I am currently using E1 trunk on cisco voice gateway (2911) to connect Telecom. Now I would like to add another E1 trunk as well as another router (2911) to increase outlines and redundancy. I am having two cucm cluster and using H323 between ...
Does anyone have access to CUCM 9.1 to confirm if ring once on active calls works in CUCM 9.1?I have used this feature it in the past in CUCM 7 and 8 just fine. This client is saying this doesn't work and it only beeps when a second call comes in.I a...
Hi,I have tried altering several phones to use a new softkey template, though the phones will not update to this sofkey template, despite applying+restarting, and also physically rebooting the phones!Has anyone seen this? I am not aware of any depen...
Hi Folks,I have a site who is in Rio, Brazil whos cell phones has been changed from 8 digit to 9 digit. In order for me to comply I need to update the dial peer/plan for CME 8.6 . Anyone who can give advice or instructions is appreciated.e.gExample: ...
Greetings to all.i had a problem to establish a voip session between 2 sites as despicted on picture.on site left, i had an 2851 ISR Router with running call manager express, in the other side of the tunnel gre i had an 2801 isr with fxo and fxs port...
I'm using cucm 9.1. I want to give Read only rights on Personal directory to some of my IPT users.How can i acheive this in CUCM 9.1.Regards
Hi,does anyone know if its possible to syncronize call-lists (placed calls, missed calls etc) between phones sharing the same line?Regards, Frank
