Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hey Guys,I'm wanting to change a incoming number block to another internal range on a h313 gateway.ExampleIncommingchange12345XXXto12346XXXthen swap it around for out going123456XXXto12345XXXWould this be correc for incomming ?Voice translation-rule ...
Hi,We have one OU include all the users. We are not able to create sub-OU that include IP Phone user only.That the One OU that also include a lot of user that doesn't have IP Phone also.My question is simple, I don't care to sync all the users, but ...
Hello Everyone, Could you please help me!!As per the current setup: I am using Directory numbers in Hunt group configuration of Attendant console pilot; instead of username and line number.Want I want is : If no one is logged into Attendant console ...
Hello All,We have some num-exp configurations which translate 5 digits number to international numbers. For examplelnum-exp 345.. 900321131345..The issue is that there's no ring back tone when we use the num-exp but there's ring back tone when we dia...
hi all,i configured uc540 with 11 phones , but the problem is my device is automatically restarting after some hours . wireless in the uc540 also disconnecting automatically.some tomes it will restart twice or thrice and then stable state and while r...
Hi,I have a CISCO Unity connection 7.1.X . I would like to know whether the users can view and manage thier voicemails using explorers.If so what is the link used?Faizal
Hello all,the question is following:I have two dial-peers on CCME with a) destination-pattern 9.......... (10 digits without "9") b) destination-pattern 900............ (12 digits witout "9")how to configure CCME that it will select dial-peer (b) wh...
Hi,I have the CME in the router 2800, i want to install a basic Auto Attendant, with just a Welcome message when someone call to the office, but i search in the internet and just found materials talking the configuration with service-module installed...
I am having issue with WMI for the following scenario.I am having couple of sites but each site uses 4 digit extension. It uses 2 digit access code to call each other site. And we are planning to use a single unity connection server for all site. Fol...
Hi All, In CUCM feature and services documents, it shows how presence works in corporate directory but it doesn't show how to configure it. if you show me how to configure presence in corporate directory, I'll be very appreciated. thanks Alex
Hello Experts,I am using auto QOS in the switch level (3750) and need your help to configure the QOS in the router (3845). We have 2Mb bandwidth on the WAN side and we do video conference quite often. Could you please let me know what would the best ...
I am trying to create VM using BAT but for some of the users I receive the following error message "Contact with the specified extension already exists in the Partition". Could you please let me know what the problem is and how can I relove this issu...
Starting today on our Communications Manager 8 when calling into any extension it rings once on the caller end then silence then goes to voicemail if unanswered.....What do I check for why there seems to be no ring?
Hi all ,i am getting ring back tone when i am dialing a mobile number which is switch off. there should be a recording from the mobile company .if i am dialing the same mobile number from my mobile its responding the called mobile is switched off. bu...
HiHave following issueInstead of displaying the user's calling ID, the group number shall be displayed instead.Our sip proxy is fixing this.When I had done that, the problems started.The spa942 will not longer response on the 200 OK.Thats means that ...
| User | Count |
|---|---|
| 8 | |
| 4 | |
| 3 | |
| 1 | |
| 1 |
