Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi I have a problem with Extention Mobility, the service Cisco Extension Mobility this configuted Maximum Login Time in 8:00 but the ip phones to make logoff after 5 minutes. The choice Enforce Maximum Login Time is true. Any solution?Thank you
Hello,I would like to create a conference using calls on 2 different lines on a Cisco IP phone 7931.I followed the procedure here below that I found in the "Cisco Unified IP Phone 7931G Phone Guide for Cisco Unified Communications Manager 6.1(SCCP)" ...
Hi everybody,I have a problem to dial number with Click 'n Dial.I use the application with a Mobility Device Profil and not a Fixed profil and has tick the CTI control for the user and has the Extension Mobility activate for the Cisco phone 7960.I c...
I guess I know the answer to this, but was wondering if there had been any developments in CUCM6.If a user picks up a call on another extension using call pickup, the original extension logs a missed call (even though this call has been answered), is...
all , i have bought the nokia icc license . from my e71 , i was prompt for a 12 digit license code which i cant find on the nokia license purchase confirmation letter.the letter hav a 10 and 11 digit number but dont see a 12 digit code.i am using icc...
Hi,I have 3 out of 24 VG224 ports stuck in off-hook status. I resetted the port 7 main gateway (mgcp). Version of ios is as belowvg224 Software (vg224-I6S-M), Version 12.4(5b), RELEASE SOFTWARE (fc2).I usually experience this problem on other VG224 a...
Does anyone know if CM 4.2.3 has the ability to run a ext mobility report based on when a user logged On/Off?
I`ve just installed 6.0 CUCM and have 50 license for handsets and a node license being shown , I`ve created 3 x devices and the number of units have decreased in the reporter but the phones are not registered. Are these licenses real or do I need to...
I need to mask the outgoing number ID for a particular DN and I need to be able to do it from within call manager 4.2 as opposed to on the Gateway! How do I go about doing this? Anyone? : D
CME in SRST mode yields up/up dial-peers for the ephone DNs. This results in no inbound calls. Have the exact same hardware/IOS/config on another site and it works properly. Baffles me. Anyone run into this before?CME 4.1IOS 124-15No ephone's registe...
Greetings!It has been some time since we have updated our compatible list of headsets with our cisco phones.Does anyone have a list of the headsets plantronics manufactures that are good quality (these will be used for our operators).Currently the on...
Hi Chaps, easy questionUCM6 - is it a SQL backend database that is used? if so - during a new installation is it possible to host the sql database on an external (corporate) SQL server?Thanks in advance.Rod
Hi Guys,I am trying configure any parameter: region, location, user, etc.. and I receive the message "error on page". This version is CCM 4.2.1. What could is occuring? any ideia?Thank You, Wilson
I have a VG224 registered via SCCP to CCM6.1. From FXS to FXS on the VG224 the calls are fine, but from FXS to IP phone I only get one way audio even though DTMF tones pass through in both directions. The VG224 and the IP phones are on the same vla...
CUCM 6.1 new installation, 4 nodeInstallation on HP DL380G5 machinesEverything appears ok, but the call manager service on each of the 4 machines stops after about 20 seconds. All other services running. If I start Call manager service it shows as st...
