Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,I'm trying to create a voice dial-peer where I can dial 7 digits but only have 4 of the digits forwarded to the appropriate GK. example:dial-peer voice 1234 voipsession target ipv4:myGKipAddresscodec g711ulawdestination-pattern:555....In destinati...
Hello everyone,How can I setup account codes (for time tracking and billing purposes) on Cisco CallManager Express?I know using Account Codes and generating reports on CCM4/UCM5+6 are great!Some of the docs I been reading states that creating a SoftK...
I've been reading around this... is this possible ?I am using a 1760 as my Gateway, I have FXS and FXO, I would like to have voicecalls inbound on the FXO go to CCM and onto IP Phones, and the FAX to go to the fax machine on the local FXS port.1. is ...
I'm getting the follwing error through RTMT[RTMT-ALERT-CCM-PUB-Cluster] SyslogSeverityMatchFoundAt Tue Oct 07 11:30:46 PDT 2008 on node 10.1.12.10, the following SyslogSeverityMatchFound events generated: SeverityMatch - Alert kernel: IpVms: No free ...
Hi all, I want to configure a NME-CUE module. I have the following configuration: interface GigabitEthernet0/0 description Inside net ip address 10.85.1.150 255.255.0.0 ip helper-address 10.85.1.11 no ip redirects no ip unreachables no ip proxy-arp i...
I have a FXO port connected directly to an exchange line, when I ring this line and look at the "show vOICE PORT SUMMARY" output I get the following:Operation Status StatusDorm ring-det on-hookup idle on-hookit alternat...
Hi, i have one 2821 with ios c2800nm-ipvoicek9-mz.124-11.XW2.bin. Even with logout-profile and user-profile configuring, my 7940 show the message of "host not found". Not showing the option "Extension Mobility".What could you help me?
Is there a way to record calls in CUCM 6.0(1), or is that going to be handled with a third party software or appliance? I know Cistera does that sort of thing, but I wondered if CUCM could do it without a third party anything? I have not seen anyth...
Good evening everyone. Hope someone can help me figure this one out. This past weekend I converted a client from a Nortel Option 81 to a Cisco system running 6.1(2). The local PRI's came up just fine but the long disatance T1 never came up. I get...
Yesterday I started having problems with a user that has been unable to disable call forwarding from the phone. I can go into CM and remove it from the device line properties and reset. At first I thought it was just a phone or button issue but it ha...
I have a network with a central CCM and a TDM PABX which is being replaced with SRSTCCM >>>>>>>>>>>>> h323 gw>>>>>Network cloud>>>>>>>>>>.h323>>>>>>>>qsig>>>>pabxQuestion We need to keep the H323 GW in place as they act as a demarcation point for o...
Hello all,iam trying to configure my BRI wic with ISDN line from Deutsche Telekom but without success with this message:"**ERROR**: Ux_BadMsg: Invalid Message for call state 11, call id 0x8007, call ref 0x5, event 0x62". I can calling everywhere, i c...
Can I upgrade Unity from version 4.05 directly to version 7. I cannot find documentation for this version upgrade. My local PSE says this can be done. TAC has mixed results. One engineer says yes, another said no.....go figure. Has anybody done this?
I have a cm 6.1.2, the problem is that when i receive an international missed call i can not reial the number because the 00 is missing from the number (example: 944161....)The call manager is connected to pstn gateway but there are no translation ru...
Hi everyone, does anybody knows something about this message appearing in the IP Phones "High Traffic Try Again Later", i was doing a little research and i only found this in a Call Manager 3.3 or 4.1 design, im using CUCM 6.1 latest version.Regards
