HiI have configured a FXO voice port for inbound calls.these calls are auto redirected to a number. I have seen that this port hangs when the PSTN peer diconnects. Can any one guide me on how to deal with this matter.ThanksMahdi
HiI have configured a FXO voice port for inbound calls.these calls are auto redirected to a number. I have seen that this port hangs when the PSTN peer diconnects. Can any one guide me on how to deal with this matter.ThanksMahdi
Dear All,I installed the Sip Proxy 2.2 according to the config guide, i try to start it up, but the sipd disappear without log.What should i do?
Hello What is the role of OPX in voice gateway? what is the meaning when opx has a value like: opx=9, opx= 602,602,603 ? why FXO has OPX value but in other hand FXS Doesn't have OPX Please could you help thanks a lot
I am trying to run reports on how many of our DID numbers are being hit. Right now they come in over our PRI trunk group into a cmm. I've built translation patterns to direct them to the appropriate internal line. All works fine.But, CDR only reco...
HiCan CM4.1.3 do Overlays like CME or can I do some kinda workaround?Thx
HelloI have configured a sequential huntgroup where I have 3 groups that I want to pass before I reach the final number.My problem is that it never rings in group 2 or 3. It jumps directly from group 1 to the final number.Here is a piece of my config...
I have a customer that is migrating from their old CCM 3.x setup running on an ICS 7750 to a new CCM 4.1.3 cluster running on an MCS server. They also have Unity VM only installed but I am not sure what version it is but it was installed the same tim...
Hi,I am using CME3.3 with my ip phones configured to be members of different Hunt Groups. What I would like to configure is that when an incoming call is displayed on the phone it also gives an indication of which hunt group was called. Each hunt gro...
Hi People,Anyone help with this strange issue?If a user is on phone, I can call that user and ring back, whilst the user gets the call waiting beep. However if I press any keys while its ringing out, the user with call waiting hears the dtmf tones as...
Can someone please confirm if the IPCC Express IP Phone Agent works with the 7920 Wireless IP Phone?? w/ V.2 software?Or how about what about the Desktop Agent? Does it support the 7920?PS. I know V.2 of the 7920 software is suppose to support the SE...
Hi All,Can someone please confirm the maximum number of line appearances for the 7920 Wireless Phone w/ v.2.0 software?According to the 7920/CM4.X admin guide, it just says "multiple".What's the maximum?thanks,Paul
Dear All,I prepared a console cable as stated on the cisco website, but it didn't work, is there any extra configuration needed to be done to console the Phone ?Thanks in advance.
Hello,could you please explain me what is the difference between telephony over IP and voice over IPThanks a lotzahida
A few of my users complained that some of their messages had a very loud screetchy noise at the end of it; after 10s or so a busy signal that would play almost forever; I stopped the thing at over 2mn! and never got the options for the message.Anyon...
We have changed our Administrator password in AD and now our Corporate Directory button on our Phones don't work. Where do you adjust the credentials in CM for the Active Directory Connection?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-17-2024 05:55 AM | ||
07-15-2024 12:39 PM | ||
07-09-2024 04:24 AM | ||
06-20-2024 05:44 PM |