hiin my central router i have 3 VMIC-2MFT-E1 cards so from one card (2 ports) i want to connect to 2 different branches, only data is it possible using this card.Binoy.
hiin my central router i have 3 VMIC-2MFT-E1 cards so from one card (2 ports) i want to connect to 2 different branches, only data is it possible using this card.Binoy.
HI There,Is any one experience this error msg,What does this mean,,,what is the Solution to fix this problem....Below is the error msg:-System was restarted by error - a SegV exception, PC 0x802000FCC2600 Software (C2600-JS-M), Version 12.0(8), RELEA...
A cat 4000 with ios 12.2.18 running with policy based routing must be upgraded to 12.2.20. I want to know if all the policy commando's are supported in this version. Is there some documentation? I can only find something from 4500.Thx
Hii have 2 types of e1 cards 2MFT-E1 and NM-2CE1T1-PRIso if i give Line code hdb3framing crc4clock source line it will work is it.also Clock source internal Line code amiif my telco supports both types of line code i can use any is it.actually what'...
Dear all,I want to remove bridging connectivity from my network. Presentally my network is like this.We have five remote location and my central office in new delhi. all the remote location is connected bridge over WAN for data as well as voice commu...
I had configure my router to NAT 2 external IP range.NAT translation works fine. but, Problem arise when i need to telnet to the router. i.e.:my Fa0/0 ip: 10.0.0.1, and my nat pool 10.0.0.10 - 10.0.0.20.it seems the replying ip was taken from the NAT...
I have an existing site using 192.168.26.0/27 being advertised in our OSPF network. We are statically routing to the new site from the router at that location to their core router. They have a 192.168.26.0/24 network. We are performing NAT where they...
I have a 2651XM which has IOS version 12.3(10), RELEASE SOFTWARE (fc3) and System image file is "flash:c2600-i-mz.123-10.bin. When I try to go to controller T1 0/1 and try channel-group 0 timeslots 1-7 speed 64 , it works fine. But then when I try to...
for VoIP, we do:class-map match-any EF description Expedited Forwarding PHB match access-group name PriorityPBXclass-map match-any Default description Default no PBX traffic match access-group name NotPBX!!policy-map SETDSCP class EF set dscp...
Hi,I need help in allowing the internet to access by our warehouse.Scenario 1:We have three routers installed1. Internet Router2. Head office to Warehouse interconnection3. Warehouse to head office interconnectionScenario 2:Internet router and (Head ...
I am contemplating of migrating from HSRP to GLBP. Besides the inherent advantages, can anyone give me a feedback on its use on a production network? On what IOS is it supported?I am Thanks.
Hello.This is john.How can i change bgp router-id without any effect?I have to change bgp router-id because interface ,which is used current bgp router-id, does not use anymore.Regard,John
I got a warning:* WARNING: This software is designed to work on c2600 systems ** with byte accessable WIC slots. ** You should not continue to use this software if you ** plan to use WIC cards. ...
Will Cisco NAT TCP Load Dist work with a pool of real host addresses which will then be portmapped using Kerio firewall software ?
Hi therePlease correct me if I'm wrong (which I most likely is...). When using "eigrp stub", am I supposed to get a default route or a copy of the entire routing table on the stub router?Otherwise how do I only advertise a default route to a stub rou...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM | ||
11-08-2023 03:38 AM |