Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

“Webinar

 
Labels

Forum Posts

Start a conversation

Resolved! 1841 ADSL 2+ Issue

Hi,     Wondering if anyone out there may have an answer to my issue with one of my customers ADSL 2+ / 1841 problem.I'm in the UK, and have a customer who has an 1841 with a HWIC1 ADSL. He has just upgraded from ADSL to ADSL 2+. I have an ADSL teste...

markeelen by • Level 1
  • 2377 Views
  • 11 replies
  • 0 Helpful votes

Resolved! WAN Redundancy

                   Hello,I know that with Serial interfaces I can do MLPPP but so far what I have seen says that the serial interface get a "no IP address" and joined to the multilink bundle which has the IP address.  What can I do to bundle somethin...

Cisco 2911 and NAT Configuration

I have a Cisco 2911 router that I am trying to edit/add to the NAT Configuration through Cisco Configuration Professioanl.  The issue I am having is when I go there to edit an exisiting entry or add a new one none of the buttons are working.  I can c...

hodgson.c by • Level 1
  • 6656 Views
  • 3 replies
  • 0 Helpful votes

Hi, this is kishore

Hi, i'm working on Eigrp. I issued the command ip bandwidth-percent eigrp but i dont know how to check is this command working fine.I Tried traceroute before issuing this command it should that the network is load balanced. But still after issuing th...

Resolved! PPPOE username

                   I am attempting to bring up a remote router using a pppoe connection by replacing the current Tenda 308R router with a Cisco 1921 using the ethernet connection on the WAN side.  The connection works fine with the Tenda in place but...

Resolved! IP SLA Failure

Below is a very simple IP SLA configuration.  It is designed to monitor traffic across an Metro connection (10.100.8.1)  and if that connection goes down, route through a VPN over the internet to the remote end (10.1.1.42).    Track shows reeachabili...

DrVoIP by • Level 1
  • 4259 Views
  • 4 replies
  • 0 Helpful votes

6503 switch or 7201 router ?

Hi,I am looking at running MPLS from from one datacentre to the other (we have a layer2 interconnect and can run jumbo frames)I need about 70 access ports (each in a seperate VRF) at the new datacentreI am looking at :2x 6503'-Es with sup720-3B and a...

mcroft by • Level 1
  • 618 Views
  • 1 replies
  • 0 Helpful votes

One router with two WAN connections

Hello  I have one more scenario, at my branch office, I am having one router with my Cloud network and internet on this interfacesRouterint f0/0des Connected to LANip add 10.x.x.254 255.255.255.0int f0/1des Connected to Internetip add 62.x.x.21 255.2...

Resolved! Two Routers Connectivity in LAN

I am having two routers of 1841 series.In router 1 I am connected with my Cloud Network and in router 2 I am connected for internet.I need both the wan connectivities to be advertise in my network for my LAN which is configured with DHCP in my ROUTER...

Help with NAT using specific ports.

Hello,I have a customer who is requesting that we allow inside host 10.1.31.10  over ports 5060, 4569, and 10000-20000 to connect to remote host 201.63.34.87. The inside host should NAT to 201.94.234.23I have an idea on how to do this using route-map...

HWIC-3G-HSPA and Optus

hi,We have a 1921 router and 3g card. We have tested the 3G card in a PC and logged onto the networ successfully. We have setup the router with the below settings and the cell0/0/0 interface constantly bounces. Are there any Optus specific settings t...

Resolved! Switchport VLAN port changed

Hi, My collegue complaint that he cannot connect to VLAN80 using the port connected on his desk. I checked the switch where it is connected and below are the config:He is using port fa0/13. sgsinspark-10651225#sh run int fa0/13Building configuration....

View All
Review Cisco Networking for a $25 gift card