Hello guys, I am currently trying to distribute IPv4 BGP Packets through my IPv6 Backend. I am able form adjancencies between all "needed" Routers, however the Routes don't seem to be forwarded. Current Configuration: Left-breakout (A1-POP1)rout...
I installed a new PID: EHWIC-4ESG on a cisco 2901 , but it is not showing up in the sh ip interface brief Getting below message in the log:EHWIC IPCORE PLL PLL Failed to LOCK in 0/2/0 ehwic slotAny suggestions on how to fix itCisco 2901 version is:...
I Have a number of Cisco 897VA's. I have configured service-policy output QOS-897-WAN-OUT-PARENT on G8. However when i try to configure it on G0 as well it fails with the following error.#service-policy output QOS-897-WAN-OUT-PARENTConfiguration fail...
Hello,I have a STB which need to access to file on the router.Because I replaced the ISP Routeur by a CISCO one I need to redirect port 80 coming from STB to Router (which is a default gateway) to a local HTTP server.STB : 192.168.1.3Router : 192.168...
Hi, I have my switch core connect to my sdwan router. My branchs are addressed with this block 192.168.0.0/16 but i have some servers using this network 192.168.146.0/24. Static route on sw core:ip route 192.168.0.0 255.255.0.0 SDWAN ROUTER IP When i...
interface Dialer1mtu 1480bandwidth 6000ip address negotiatedip nat outsideip virtual-reassembly inzone-member security outsideencapsulation pppip tcp adjust-mss 1400dialer pool 2dialer-group 2ppp authentication chap pap callinppp chap hostname sakkhr...
Hi all,i have an interesting issue with asr 1006 and cgnat. Happends once per 2-3 months.The customers reporting issuew with browsing. The need to refresh page in browser several times to load the page. The speedtests are ok, ping are ok, no packet l...
Hey Guys,So i must do dynamic routing with the protocol RIPv2 on the packet tracer. I can't find the issue. Notebook 1 can communicate with Router1 only not Router2 and Provider2. Notebook 2 can communicate with Router 1 such as Router 2 and Provider...
Hello all,Is there any difference between vrf lite and vrf????can i configure both on cisco ISR router 4331 ?any content of vrf or vrf lite is welcome. Thanks!!!!!
Hi all and happy holidays, we have an ASR1013 current IOS-Version from 6.12: 6.8.2 and previously we did not had problems, but few hours after activate of LACP Te0/2/0/20 we got this issue: many ports does not work with Paket-Types (CDP, ARP, ND, LAC...
I have the following scenario:Lets suppose the switch is an ISP that provides a VPLS service to connect the 3 routers so they can established an ISIS neighbor relationship. I want to make sure that the traffic from one PE to another PE goes first to ...
To configure WAN, you use serial port (cable) to connect among routers. Why do we use only serial port? Can't we connect by Ethernet?
I have 3 2911 routers and 2 3560 v2 L3 switches and one 2960 L2 switch. I have my network setup and everything works except I can't ping my home hotspot router or access the internet through it from anywhere on this network. . Here is my setup:R1s0/1...
Hi Cisco Community,I would appreciate some troubleshooting or advice. For reference, please check my simple network map attached to this post.The Problem: I cannot ping my DHCP Server / Router (192.168.10.1) through the client PC even when manually a...
2 computer rooms, 2 lecture rooms, server room, wifi for students and a separate one for teachers. This is the project i need to do. Maybe is someone who can help me. I've already done most of it, I can't get on with the wifi part. i dont know how to...
