By doing a debug on both router that are participating in the authenication, this is what i get. This is an ISDN backup. Any ideas? Output attached.
By doing a debug on both router that are participating in the authenication, this is what i get. This is an ISDN backup. Any ideas? Output attached.
Ok here is what I did; but doesnt seem to function.switch 1config tint range g3/9 -13, g3/19channel-group 2 mode onint po2switchportswitchport trunk encapsulation dot1qswitchport mode trunkdescription Trunk connection for L2 Vlans to r2-Router switc...
I am new to cisco routers and I want to make configuration to a router that if someone ping, or any traffic generated, by pc or any device, all the log should forward to my pc, (or to my email).waiting for a descriptive reply,Zahid
I have worked upon the bellow topology to get a grasp of Frame Relay but I bumped into EIGRP routing, which I don't remember much. It's been 2 years since I went through CCNA3 and haven't been dealing with it since then. I will most likely review it,...
I have a question you do do remote access ssh and telnet remotly to a 2960 switch?
Dear AllI have an issue with cisco 7609. You can refer the topolog belowPCs-------->Router(7609)------------------------->ISP A ------------------------->ISP BMy router have connected to two Uptream Provider(ISP...
We are seeing the latency of our AF31 class traffic increase by ~30ms when the WAN circuit is saturated. We are using a carrier MPLS service offering with Custom Queueing on the CE router which is Cisco. We only see this symtom with one carrier and...
Hi all,I have the following problem.I have a router that sees a remote network through two paths that have equal cost.However one path is under unitlized and the other is over half used.Is there there anything else I can do to better utilize the two ...
Hi all,I am looking into bringing up a remote site about 3-4 miles from my Data Center on 4 localPoint-to-Point T1 circuits. These are local Pt-to-Pt T1's so there will be 4 T1's at each end and I'll be providing my own IPaddresses. These T1's will b...
Working with the customer, all their sites are connected to the service provider via eBGP. One of the sites (see diagram router C) will be relocated, they want to keep the same AS nubmer in the new facility (see the diagram router D), During the tran...
I have a problem how can you open up a port on a Layer3 switches, I do not know if that is possible?
Was playing with qos pre-classify feature and found what:class-map match-all CLASS match protocol telnetpolicy-map POLICY class CLASS set dscp af11!!interface tunnel0 qos pre-classify ... tunnel source x.x.x.x!!interface f0/0 ip address x.x.x.x ... ...
Hi allI was hoping for some help on the following issue,The license has been installed onto the router. Here is the relevant out from the show license all:License Store: Primary License StorageStoreIndex: 0 Feature: ipbasek9 ...
Hi All, I have a AS2511 device connected to the console ports of two switches console. I needed to have a LAN connectivity to these switches from the AS2511 device. Can we use the RJ45 serial ports in the AS2511 to achieve this?CheersMikey
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-11-2024 01:54 PM | ||
07-09-2024 05:41 AM | ||
07-03-2024 08:54 PM | ||
07-02-2024 04:20 AM | ||
06-28-2024 11:08 AM |
User | Count |
---|---|
14 | |
5 | |
4 | |
3 | |
2 |