Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

I'm setting up a stub area with 2 routers over a switch. I'm having a  problem with getting the adjacency through the switch, but I get it if I  use a crossover cable.Besides the ports being active on the switch is there any other configuration that ...

Can anyone point me in the right direction? i don seem to get my cisco router to work in my house. I have a comcast cable and which is connected to my little linksys router. The little linksys router is 192.168.20.1 and the g0/0 ip address works on m...

canakweze by Level 1
  • 1689 Views
  • 6 replies
  • 0 Helpful votes

Hello All,A friend came to me asking a question regarding the output below, but given my novice level I have been unable to help.  Below is the sh cdp neighbor command from a Cisco 3550 Switch that is connected to a Cisco 2821 router.  The question i...

Hi,Just wish to ask the below.1. If i do a traceroute from a workstation directly connected to a router, to a destination that goes through the tunnel interface L0 of that same router, will the tunnel interface IP show on the traceroute results?2. If...

Hi all,One of my customer want to upgrade own network. In Attached diagram there is showing two locations, one is Registerd office(RO) and another is Factory.In Registerd office customer has 1 MBPS internet link with 768 KBPS MPLS link terminated on ...

We have four siwtches all with VLAN 10 running regular perVlan Spt.They are all cross connected to each other so you can get from one switch to any other switch via only one hop.max age = 20, forward delay =15,  MAC timtout = 300The root bridge is on...

jschweng by Level 1
  • 2327 Views
  • 5 replies
  • 0 Helpful votes

Hello All -I have two Cisco 3560 SMI switches that were given to me at work and I am wondering if I can upgrade both switches to EMI? I have read somewhere you can buy the upgrade and some people say you have to buy the switch with EMI image only. Ju...

esturao by Level 1
  • 1542 Views
  • 4 replies
  • 0 Helpful votes

We use 2800 series routers and WIC-T1DSU/CSU  to terminate multiple t1s with MLPPP in the US and Canada. Now I am looking at 3 E1s in the UK (London). I found several very old posts on this. The newest one directly talking about how to terminate an E...

sysadmin by Level 1
  • 569 Views
  • 1 replies
  • 0 Helpful votes

My new Cisco routers have dual port T1/E1 cards that appear as Controllers. What would the show service-module equivalent be for these?The nice thing about show service-module is it shows the various types of alarms with a counter indicating how long...

Hi,I have a single network 192.168.1.0, now I want to create VLANsFollowing VLANs need to be createdServers - 192.168.1.0Desktop -  192.168.2.0Other - 192.168.3.0I want desktop and other VLAN to connect to internet using 192.168.1.1 gateway, how do i...

Hello,We have SLA configured for failover from primary to DBU on Cisco 871.  There are about 170 sites with the same config.  We are experienceing problems on one site.Partial Config is as belowip sla 1 icmp-echo 4.2.2.3 source-interface FastEthernet...

pkpatel by Level 1
  • 1446 Views
  • 2 replies
  • 0 Helpful votes

HelloI got Dual VPN Hub VPN scenarioAt HQ we got VPN-Hub#1 && VPN-HUB#2On each Spoke One Tunnel points to Hub#1 and second Tunnel points to Hub#2Example on Spoke3Tunnel 1 will be  Active Tunnel pointing to HUB#1 ( all traffic to HQ goes via this Tunn...