Routing

Hi,I setup a multilink 1 with 2 serial T1 lines in the group1Serial1/0:0 unassigned YES manual up downSerial1/1:0 unassigned YES manual up upran #debug ppp multilink events29w3d: Se1/0:0 MLP: Request add link to bundle29w3d: Se1/0:0 MLP: Adding link...

Hello,My task is to upgrade the IOS to 12.2(18)SXF4 size 75MB.1. Do we have to upgrade both the SUP720 and the MSFC flash SEPERATELY with new IOS?Please advise.--------------------------------D000RTR01#sho modMod Ports Card Type ...

as we know tcp works on the three way hand shaking ...1. SYN2. SYN-ACK3. ACK...my query is why TCP not satart sending data after the 2nd handshaking which is SYN-ACK... as now both the end are exchanging the required paramets... so they can start sen...

Hi,I want to limit input and output rate to a gigabitethernet interface at 200Mb/s.So, following the rule:bc=(rate/8)*1,5 secsbe=2*bcthe command look like thisrate-limit input access-group <ACL> 200000000 37500000 75000000 conform-action transmit exc...

Load balancing for serial link for OSPF has been configured using backup load. Backup line is a PRI line calling another PRI line. both pri are configured for loopback address. so in output of show ip ospf nei command it shows neighbor relationship ...

hi All,I need another fast ether int on my 2800 series router. I found the HWIC-4ESW on cisco's site. I notice that it says " Layer 2 Ethernet switches with Layer 3 routing capability. (Layer 3 routing is forwarded to the host, and is not actually ...

I've got a problem I'm trying to resolve and I haven't figured out the right metrics for this. I'm hoping someone can help. I have two connections to the Internet from two separate locations. The entire internal network is routed via EIGRP and a defa...

i have a 3-layer switch 3560 to instead a old router.because 3560 doesn't have WAN port,I have to convert fiber cable to RJ-45.what should i do?need i to configurate on the port?

Hi,I want to configure Channlize E1 on my 2600 series router on my 2600 router i have 2 wic card. The IOS version of my router Version 12.2(7b)Thanks

Dear Forum,I have a 1720 router running IOS 12.1(19) on it. It has 24MB of RAM. We have added VoIP going out on on T1 and we have problems if we saturate the line with say a download.I've read about autoQoS and am wondering what IOS version do I ha...

Hello to all,I do have query,I wanted to know that is ther any LAYER-2 or any physical addressing scheme ora any identifier exist on serial link of cisco or any other vendor proptitary. So we can chek out the ARP on cisco routers connected by serial ...

when i check my router 2500 with sh run command it shows ip 192.168.41.1 configured on s0 port, but when i check router with sh conf command it shows ip address 192.168.1.1 on s0 port . How is that ? please explain me

i need to add 3 route to our switch 3650192.168.40.0192.168.41.0192.168.42.0how can in make it , give me commands

What is mean of wait timer in ospf ? and how it differ from dead interval ?

as show ip route tells i cannot find Cisco documentation for "forward metric" ... what is it ?our-6509->sh ip route 172.23.0.0Routing entry for 172.23.0.0/16 Known via "ospf 1", distance 110, metric 20, type extern 2, forward metric 21 Last update ...