Hello,i have receive today my Cisco 2960L-16PS-LL Switch.What is the standard user and password for the Web GUI?I have try it with cisco / cisco but it is not working.
RegardsMichael
I want to apply an ACL to a couple of VLANs in my network of Catalyst 3750 switches (operating in layer 3 / IP routing mode). One point on which I am not clear is whether I need to create and apply the ACL on each switch, or whether I can create it ...
hi everyone,
I m changing a PFSense router with a Cisco. And I m bit stuck with the configuration ( the NAT rules ).
In the attachements you'll find the Pfsense NAT configuration table with the ACL used for that.
Please help me translate it to CISCO...
Greetings, I am trying to configure an ME1200 right out of the box, and some of the most basic commands do not work. For instance when I type in show run I get an error message command not permitted. If I type a question mark I get the following:
AC...
Hi team !I'm trying to get the CPU Utilization of my SG220-50 50-Port Gigabit Smart Plus Switch : I downloaded the correct MIB directly from CISCO for the version 1.0.0.18 (link below), but even with it i can't find the correct OID to get the CPU.I t...
Hello
I can ping ip 10.10.10.10 but can not ping ip 10.10.10.16 from internet router?!
Jeddah#ping 10.10.10.10Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 10.10.10.10, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), r...
Hi,
I'm looking at some diagrams and there are one portion of Tier 2 Network and another portion of Tier 3 Network.
Tier 2 Network has L3 switch that is connected with F5, App servers, and firewall.
Tier 3 Network has another L3 switch that is conn...
All,
I am looking at setting up SNMP v3 traps on my routers and switches. What software is commonly used to collect (and notify) of the SNMP traps from Cisco devices? I cannot seem to find a clear cut answer, or someone saying, "This is the best SNM...
Hi,
I have a 4 switch HSRP group with the following HRSP priorities configured on a VLAN. All switches have a 180 second preempt delay configured.
Switch 1 (Active) - Priority 140
Switch 2 (Standby) - Priority 130
Switch 3 (Listening) - Priority 1...
Good day.
How can I check LAG interfaces status changing via snmp ? What type of oids I can use for
1) checking joining / unjoining status of interfaces in LAG
2) checking time after last joining.
3) checking LAG mode on interface (lacp/pagp)
4) che...
I was reading one of the slides from this year Cisco Live regarding VPC. One particular slide kinda confused me (attached). My understanding of setting up backup route path with VPC is: Use a dedicated L3 link between the two VPC peers for dynamic ro...
Hi All,
I have two questions please, is it possible to advertise networks in BGP with only the
1 - is it possible to advertise networks in BGP with only the ip prefix-list or route-map WITHOUT redistribute or network command?
2 - if I configure BGP...
I have a WS-C3560X-24P that is running Version 15.2(2)E3 getting this error 1 min to 5 min intervals. I cannot find anything on this error to explain why it is getting this. Is there a bug that I am missing?
Jul 26 08:01:54.130 EDT: %IDMGR-3-INVALI...
hi,
after configuring MST
one of the switches I am not sure why it was showing this when I inserted command "show spann vlan 10"
Fa0/19 Mstr FWD 200000 128.21 P2p Bound(PVST)
however MST was configured on this switch. when I shut...
Hi,
I am facing a issue whereas we have Active/Standby Failover setup - ASA 5555 where as
1. Active Firewall IP : 10.x.x.2542. Standby Firewall IP : 10.x.x.253For this common IP for managing FW is : 10.x.x.1
Rule :User informed that he is not able ...
